Annuler
Ce produit n'est pas disponible dans votre pays.
Numéro d'article: IF145-088-1
Ce produit n'est pas disponible dans votre pays.
7,99 $US
Discount iFixit Pro appliqué. Reg :
7,99 $US
Les pièces d'occasion A-Stock sont en excellent état
Les pièces B-Stock ont de légers défauts cosmétiques
Les pièces C-Stock ont des défauts cosmétiques majeurs mais sont entièrement fonctionnelles
7,99 $US
Discount iFixit Pro appliqué. Reg :
7,99 $US
En rupture de stock
Prêt pour l'envoi
Prêt pour l'envoi
En rupture de stock
Nous vous enverrons un message lorsque le produit sera à nouveau disponible.
En rupture de stock
Prêt pour l'envoi
Nous n'avons pas suffisamment d'articles en stock
%Livraison gratuite pour toute commande supérieure à 100 $US ou contenant un Pro Tech Toolkit !
Parcourez notre boutiqueDétails du produit
Description
Description
Insulate while you color coordinate! Protects solder joints and wires in 6 lovely colors.
Great for color coding wires, tools, pens, and toys.
Assorted colors: Red, Yellow, Gray, Blue, White, Green
Histoires de réparations
My daughter cracked the display (a drop, of course). The power of a Sonic Screwdriver was insufficient to repair the screen.
Not well. This was the first device that I was unable to repair.
The iPad 2 has a repairability index of 2 (on a scale from 1-10 where 10 is "great!"), primarily because there is *so* *much* *glue* used. Even with the heating pad and spudgers, removing the screen was a Herculean effort. Even slight leverage cracked it further, leaving lots of little bits of glass everywhere. In retrospect, I should have covered the front with clear tape first.
Once the bulk of the screen was off, the next task is to remove the display and the speakers so you can get access to the little shield hat holds all three cables to the board. Because there was *so* *much* *glue*, I had a hard time seeing that the little sticker off the ribbon that's left speaker was actually still attached. I ripped the left speaker in half.
When the whole thing was finally open, I preceded to continue scraping gluey glass bits out of it.
Assembly is in the reverse. I had underestimated the number of screws and did not do a great job of labeling the clusters. When attempting to reassemble the cable connector cover, I used one slightly longer that, when tightened, pulled its anchor bolt out.
Upon powerup, it is stuck at the Apple logo. Normally, I'd be tempted to disassemble and diagnose, but I may have to accept defeat.
When dealing with a cracked screen, first apply smooth tape (something that will let you get a solid surface). Working with little bits of glass strewn around was a huge time sink.
It was unnecessary to remove the front camera.
Label groups of screws!
My daughter cracked the display (a drop, of course). The power of a Sonic Screwdriver was insufficient to repair the screen.
Not well. This was the first device that I was unable to repair.
The iPad 2 has a repairability index of 2 (on a scale from 1-10 where 10 is "great!"), primarily because . . .
The battery in my Pokemon Emerald GBA game was dead.
I unscrewed the screw that holds the game's cover in place and then used a knife to pry the contacts from the dead battery. This took some effort as the contacts did not want to let go. I finally got the battery out and inserted the new battery. The new battery was quite a bit bigger than the old battery but it still fit. The cartridge does bulge a bit now, but it still fits in the console and still works. It also no longer puts up the warning that the internal battery is dead.
The only thing I would say to anyone attempting this style of repair is to make sure you have plenty of light.
The battery in my Pokemon Emerald GBA game was dead.
I unscrewed the screw that holds the game's cover in place and then used a knife to pry the contacts from the dead battery. This took some effort as the contacts did not want to let go. I finally got the battery out and inserted the new battery. Th . . .
Les clients ont également acheté
