iPod touch (Gen 2) Replacement Battery

  • iPod touch (Gen 2) Replacement Battery / Part Only
  • 360°
360
iPod touch (Gen 2) Replacement Battery

$14.99

$14.99

Nous vous enverrons un message lorsque le produit sera à nouveau disponible.

Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12

Détails du produit

Description

Description

Replace a dead or damaged battery for your second generation iPod touch with this part.

Remarque

Lithium ion battery shipping regulations limit the shipping methods for orders containing batteries. Domestic orders may only be shipped via Standard shipping. iFixit is not able to ship batteries internationally or outside the contiguous US at this time. iFixit Customer Support will contact you if your order needs to be modified after it is placed.

Remarque

Installation requires soldering of battery to logic board and will require the following additional tools: Soldering Iron, Solder, Tweezers

Attention

Lithium-ion batteries pose a fire hazard if they swell due to age or defect. Learn more about safe handling and proper disposal of all batteries.

Compatibilité

Histoires de réparations

Mon problème

Wife's 32G IPod Gen 2 died...dead battery. Earlier, I'd used an IFIXIT kit to replace a battery in a IPhone 4 and decided to tackle another Apple product.

Ma solution

Repair went perfectly. The hardest step was the initial removing of the screen from the case. (I did find that very careful use of an Xacto knife . . .

Mon problème

Wife's 32G IPod Gen 2 died...dead battery. Earlier, I'd used an IFIXIT kit to replace a battery in a IPhone 4 and decided to tackle another Apple product.

Ma solution

Repair went perfectly. The hardest step was the initial removing of the screen from the case. (I did find that very careful use of an Xacto knife . . .

Mon problème

The device was still relatively useful and the repair isn't too hard.

Ma solution

Quite easily - the hard part is getting the case apart.

Mon conseil

Use the metal thin tools to release the plastic bezel - the cable to the digitizer is super fragile so be careful removing the bezel after releasing it.

Mon problème

The iPods were eating battery juice a lot quicker than when they were new.

Ma solution

On the first iPod, I tore the flex circuit to the front panel. I was having trouble locating the clips, so that may have been a factor. On the second iPod I made a full-scale guide for finding the clips and used a number 17 ch . . .

Mon problème

Could not charge or apply power.

Ma solution

Went great!! works like a charm!!

Mon conseil

follow the guide on I fix it!!

Mon problème

The battery was dead, and we didn't want to buy a new IPod Touch just cause of that...

Ma solution

It was perfect! The only "difficult" part was the soldering. But it was pretty easy in fact. No worries about that!

Mon conseil

Just do it! It's much more cheaper than buying a new IPod Touch, and if you really can't do that, t . . .

Mon problème

I went through the normal plug-in for my Ipod, and nothing. I found your site and bought a replacement battery. Installation was as easy as following the directions and looking at the photos. I didn't unplug the touch screen as advised, but had no problem bringing my Ipod back to life. It was like C . . .

Mon problème

After charging overnight my battery would go to red line in a few hours.

Ma solution

The repair went very smoothly. The hardest part was getting the ipod apart. The 7 Philips screws were difficult. Of the 7, 5 came out ok, but 2 had head damaged by the time I was done.... but there was enough left to reassemb . . .

Mon problème

Battery was not holding charge

Ma solution

Opening case hardest part ... takes a while of prying (to the point you might not think it will ever come apart).

One of the opening tools broke doing it ... I then resorted to using guitar picks to hold case open in one spot as I pry'ed in another ... eventually it . . .

Mon problème

The rubber gasket around edge is sooo delicate. I had several pieces when finished.

Ma solution

I will repair/replace gasket with bath tub calk.

Mon conseil

Need a better photo explaining the construction of front glass, plastic bezel and gasket.

Voir plus