SR8855 Disassembly
4. Disassembly & Assembly
4-1. Precautions & Main Tools
- Be sure to turn off the Power Switch before disassembling or as sembling the unit.
- Be sure to use the rated parts when replacing electronic compon ents (check the Model Name; the Rated Voltage/Current; the operating temperature; etc)
- When repairing the unit; be sure to keep water away from the ha rness and assemble it firm.
- The assemble wire harness connectors should not be slipped out when pulling out with moderate force.
- When repairing the unit; be sure to remove dust or foreign subs tances completely from the connector housing; the wire connection parts; the terminal contacts; etc.
It is to prevent any fire possibilities such as tracking; short etc.
- Check if there is any trace of water penetrated to the electric al components If so; replace the components or seal up the area with insulation tapes.
- Check the assembled status of the components after repairing th e unit Keep the assembled status the same as the previous status.
- Check its using environments (The Robot Cleaner is for domestic & indoor use:) When it is used for other purposes; it may cause major damages to the unit (operation error, broken down; etc)
- Do not Use Attics, Underground Floor; Warehouse; Industrial B uilding, Watery Area; Fire hazard area; Narrow & High Laying Areas s uch as Table; other not residential area.
- Do not have the customers repair the unit by themselves.
- Tools for disassembly and assembly Flat Head Screwdriver; Phi Ilips Screwdriver .
4-2. Main Body Disassembly & Assembly
| Category | Description | Visual Description |
|---|---|---|
| (1) Turn off main power | Flip over the Main Body and turn off the Power Switch (OFF) . | |
| (2) ASSY CASE BASKET (Dust Bin) | Press the Eject Button and separate the Dust Bin by pulling it out. Be sure that the dust in the Ceuton Dust Bin not get spilled out. | Eject Button |
| (3) ASSY DRUM BRUSH (Power Brush) | Press the locking tap (2ea) with fingers and separate the Lift up the Power Brush from the Main Body and separate it. | Power Brush |
Table Caption: This table provides step-by-step instructions for disassembling a device, detailing how to turn off the main power, remove the dust bin, and detach the power brush. It also includes visual cues to aid in identification.
| Category | Description | Visual Description |
|---|---|---|
| (4) ASSY BRUSH CORNER L/R (Side Rotating Brush) | Remove the screw with the Phillips Screwdriver and separate the left Side Rotating Brush (Separate the right one in the same way) When the rotating brush is bent or dirty; hold it with a Cautlon lukewarm steam towel and clean it. | |
| (5) ASSY BATTERY (Battery) | Remove the screws (2ea) with the Phillips Screwdriver and separate the Battery Cover. Lift up the ASSY BATTERY and disassemble the Connector | Battery Cover |
| (6) ASSY BODY BUMPER | Bemove the screws (2ea) and separate the CAP-SCREW |
Table Caption: This table outlines the steps for disassembling and cleaning specific components of a device, including corner brushes, the battery assembly, and the body bumper. It specifies the tools required, such as a Phillips screwdriver, and provides brief visual cues for certain parts.
| Category | Description | Visual Description |
|---|---|---|
| (6) ASSY BODY BUMPER | Remove the ASSY BODY BUMPER by pulling it out Separate the Connector from the Main Body . | |
| (7) COVER SIDE L/R | Unlock the tab and separate the COVER SIDE L (Separate the other side in the same way) . | |
| (8) PANEL CONTROL | Remove the screws (2ea) fastened to the PANNEL CONTROL. Press the two locking tabs and remove the PANEL CONTROL by flipping it over backwards. | COVER SIDE L PANEL CONTROL |
Table Caption: This table outlines disassembly steps for automotive components, providing a description of the action and a visual reference for specific parts. It details how to remove the ASSY BODY BUMPER, COVER SIDE L/R, and PANEL CONTROL.
| Category | Description | Visual Description |
|---|---|---|
| (9) BODY MID | Remove the screws (6ea) and separate the BODY MID by lifting it up. | |
| (10) ASSY PBA MAIN | Remove the PBA-DISPLAY by lifting it up Remove all the connectors from the PBA MAIN and the screws (4ea) And then; separate the PBA MAIN. | PBA DISPLAY |
| (11) PBA TOUCH (Touch Sensor) | Remove the HOLDER DISPLAY and separate the PBA TOUCH assembled under the INLAY DISPLAY (only for VC-RA8* Series) | DISPLAY COVER |
**Table Caption: This table outlines a disassembling procedure, detailing steps for removing components like the BODY MID, ASSY PBA MAIN, and PBA TOUCH, and provides brief visual descriptions for some
Rejoignez iFixit gratuitement pour lire le document complet (13 pages)
Nous demandons de créer un compte gratuit pour nous aider à bloquer les bots et à préserver iFixit pour la communauté.
