Introduction

In this guide, you will be able to access and remove the LCD screen from the camera's frame.

Pièces

Aucune pièce nécessaire.

Remove the following screws: Two silver 3.15mm Phillips #00 screws on the right side of the camera
  • Remove the following screws:

    • Two silver 3.15mm Phillips #00 screws on the right side of the camera

    • Two silver 2.08mm Phillips #00 screws on the left side of the camera

Ajouter un commentaire

Remove the two indicated screws on the bottom of the camera:
  • Remove the two indicated screws on the bottom of the camera:

    • The screw circled in red is a longer silver 3.15mm Phillips #00 screw

    • The screw circled in blue is a shorter silver 2.25mm Phillips #00 screw

Ajouter un commentaire

Carefully pull the back of casing away from the front. Carefully pull the back of casing away from the front.
  • Carefully pull the back of casing away from the front.

Ajouter un commentaire

After removing the back cover, several things must be removed. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.
  • After removing the back cover, several things must be removed.

  • Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.

Ajouter un commentaire

To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off. To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.
  • To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.

Ajouter un commentaire

On the front of the camera, in battery case, remove screws indicated: Two black 2.05mm Phillips #00 screws
  • On the front of the camera, in battery case, remove screws indicated:

    • Two black 2.05mm Phillips #00 screws

Ajouter un commentaire

Flip the camera over to the backside and remove screws indicated: The screw circled in red is a longer black 3.00mm Phillips #00 screw
  • Flip the camera over to the backside and remove screws indicated:

    • The screw circled in red is a longer black 3.00mm Phillips #00 screw

    • The screw circled in red is a shorter black 2.00mm Phillips #00 screw

Ajouter un commentaire

Pull the cover plate off for the two power cord jacks.
  • Pull the cover plate off for the two power cord jacks.

Ajouter un commentaire

Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.
  • Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.

Ajouter un commentaire

Remove the orange tape on top of the SD cardholder.
  • Remove the orange tape on top of the SD cardholder.

Ajouter un commentaire

Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off.
  • Open the battery cover and lift plastic piece off.

Ajouter un commentaire

Remove tape on left side of camera.
  • Remove tape on left side of camera.

Ajouter un commentaire

Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.
  • Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.

Ajouter un commentaire

Remove top left LCD bracket.
  • Remove top left LCD bracket.

  • This is a small piece, be careful not to lose it.

Ajouter un commentaire

Push down bottom left LCD bracket to release the LCD from grip. Push down bottom left LCD bracket to release the LCD from grip.
  • Push down bottom left LCD bracket to release the LCD from grip.

Ajouter un commentaire

Gently lift up LCD screen.
  • Gently lift up LCD screen.

Ajouter un commentaire

Slowly pull LCD screen to the left to remove it from the other grips. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.
  • Slowly pull LCD screen to the left to remove it from the other grips.

  • BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Bassem Tossoun

Membre depuis le 21/01/2011

201 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 4-29, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 4-29, Regan Winter 2011

CPSU-REGAN-W11S4G29

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 2

Total : 746