Introduction

Before doing this replacement make sure that you have a correct 2.5" hard drive to use. The original drive is a 500 GB hard drive, but any size could be used as a replacement.

Remove the nine 4mm screws with a PH0 screwdriver. Remove the two 6mm screws with a PH0 screwdriver.
  • Remove the nine 4mm screws with a PH0 screwdriver.

  • Remove the two 6mm screws with a PH0 screwdriver.

Ajouter un commentaire

Remove the black rubber tab on the back of the computer Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.
  • Remove the black rubber tab on the back of the computer

  • Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.

Ajouter un commentaire

Orient the computer upside down, with the hinges facing away from you. Find the black plastic piece in the SD card slot on the right side of the computer.
  • Orient the computer upside down, with the hinges facing away from you.

  • Find the black plastic piece in the SD card slot on the right side of the computer.

  • Remove the plastic piece by sliding it out of the SD card slot.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart. Continue around the entire perimeter of the cover with the spudger. Use a spudger to pry the cover around I/O ports.
  • Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart.

    • Continue around the entire perimeter of the cover with the spudger.

  • Use a spudger to pry the cover around I/O ports.

Ajouter un commentaire

Remove the two 4mm screws using a PH0 screwdriver. Depress the tabs holding the battery with a spudger. Disconnect the battery connector from the motherboard using a spudger.
  • Remove the two 4mm screws using a PH0 screwdriver.

  • Depress the tabs holding the battery with a spudger.

  • Disconnect the battery connector from the motherboard using a spudger.

  • Pull the battery up and away from the laptop to remove.

Ajouter un commentaire

Use a plastic opening tool to pop the latch up on the ZIF connector up. Pull out the ribbon cable to disconnect it from one side. The cable can be left connected to the other side.
  • Use a plastic opening tool to pop the latch up on the ZIF connector up.

  • Pull out the ribbon cable to disconnect it from one side.

    • The cable can be left connected to the other side.

  • Remove the black isolation pad.

Ajouter un commentaire

Disconnect the data connector from the motherboard using a plastic opening tool. Disconnect the data connector from the motherboard using a plastic opening tool.
  • Disconnect the data connector from the motherboard using a plastic opening tool.

Ajouter un commentaire

Remove three 4mm Phillips #0 screws.
  • Remove three 4mm Phillips #0 screws.

  • Remove hard drive with rail attached from laptop.

Ajouter un commentaire

Remove the four 3mm Phillips #0 screws located on the side of the rails. Separate the hard drive from the mounting rail.
  • Remove the four 3mm Phillips #0 screws located on the side of the rails.

  • Separate the hard drive from the mounting rail.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Nat McCormick

Membre depuis le 15/02/2018

645 Réputation

5 tutoriels rédigés

Équipe

USF Tampa, Team S16-G1, Boczar Spring 2018 Membre de l'équipe USF Tampa, Team S16-G1, Boczar Spring 2018

USFT-BOCZAR-S18S16G1

5 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 8

Total : 34