Introduction

Both front and back cameras are connected as a single assembly and must be replaced together.

Use a plastic opening tool to pry the back panel off by inserting it in between the front and back panel. There are clips that need to be released on all four sides of the device.
  • Use a plastic opening tool to pry the back panel off by inserting it in between the front and back panel.

  • There are clips that need to be released on all four sides of the device.

  • When replacing the back cover insert the bottom side first ( usb and hdmi ports stick out about 2mm ) inserting them into the covers openings will allow for easier reassembly

Ajouter un commentaire

Remove the battery connector using either your fingers or a pair of tweezers. Remove the battery connector using either your fingers or a pair of tweezers.
  • Remove the battery connector using either your fingers or a pair of tweezers.

Ajouter un commentaire

Unscrew two 1.17x2.9mm Phillips screws from the white connector port. Lift the battery connector away from the motherboard using a spudger.
  • Unscrew two 1.17x2.9mm Phillips screws from the white connector port.

  • Lift the battery connector away from the motherboard using a spudger.

Ajouter un commentaire

Remove the flat-top connector coming from across the camera assembly with a spudger. Remove the flat-top connector coming from across the camera assembly with a spudger.

Ajouter un commentaire

With the spudger, remove the flat-top connector coming from underneath the motherboard. With the spudger, remove the flat-top connector coming from underneath the motherboard.

Ajouter un commentaire

Remove the clipped ZIF data connector coming from underneath the motherboard. Lift up the black plastic clip with a spudger. Pull the connector out gently using tweezers.
  • Remove the clipped ZIF data connector coming from underneath the motherboard.

    • Lift up the black plastic clip with a spudger.

    • Pull the connector out gently using tweezers.

  • Be careful to ensure that the black plastic clip has been lifted away from the connector ribbon before pulling on the connector. The clip should be loose and easy to wiggle. Removing the connector before it is unclipped can cause damage.

Ajouter un commentaire

Remove the following five screws from the motherboard.
  • Remove the following five screws from the motherboard.

    • Three 1.5x2.5mm Phillips screws

    • Two 1.55x2.38mm Phillips screws

Ajouter un commentaire

Lift all four antenna connectors from the motherboard again using the spudger.

Ajouter un commentaire

Gently lift the motherboard away from the device. If there is any resistance, check the previous steps to ensure that all connections have been removed. Gently lift the motherboard away from the device. If there is any resistance, check the previous steps to ensure that all connections have been removed.
  • Gently lift the motherboard away from the device. If there is any resistance, check the previous steps to ensure that all connections have been removed.

Ajouter un commentaire

Use a spudger to detach the flat-top connector from the camera assembly.

Ajouter un commentaire

Pry the camera assembly away from the device, lifting the left side with a spudger. There is a small hook on the right side of the assembly holding it in place. When removing the assembly, be sure to lift it from the left side in order to slide it out from under this hook.
  • Pry the camera assembly away from the device, lifting the left side with a spudger.

  • There is a small hook on the right side of the assembly holding it in place. When removing the assembly, be sure to lift it from the left side in order to slide it out from under this hook.

Ajouter un commentaire

Insert spudger between the plastic frame and circuit board. Gently pry the plastic frame away from the rest of the camera assembly.
  • Insert spudger between the plastic frame and circuit board.

  • Gently pry the plastic frame away from the rest of the camera assembly.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Nathan

Membre depuis le 12/10/2014

632 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 14-27, Maness Fall 2014 Membre de l'équipe Cal Poly, Team 14-27, Maness Fall 2014

CPSU-MANESS-F14S14G27

4 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 7

30 derniers jours : 33

Total : 2,615