Introduction

This guide shows the process to replace the screen located on the back of the Canon EOS Rebel T6i.

First, Remove battery and ground your wrist using a grounding strap to prevent damage to device.Locate the screws on the outermost side of the screen. There are 2 at this location. Remove them using a J000 gauge Phillips head screw driver.
  • First, Remove battery and ground your wrist using a grounding strap to prevent damage to device.Locate the screws on the outermost side of the screen. There are 2 at this location. Remove them using a J000 gauge Phillips head screw driver.

  • 2 screws on the side -1.3 mm

Ajouter un commentaire

4 screws are located on the opposite/interior side of screen case. Use the J000 gauge screw driver head to remove these 4 screws. Furthermore, these screws are a larger gauge then the other 2. Please sort these accordingly. 4 small screws on back 1.58 mm
  • 4 screws are located on the opposite/interior side of screen case. Use the J000 gauge screw driver head to remove these 4 screws. Furthermore, these screws are a larger gauge then the other 2. Please sort these accordingly.

  • 4 small screws on back 1.58 mm

Ajouter un commentaire

Following the removal of the 6 screws, Locate the joint of the casing. Place a flat lever inside this crevice and apply pressure. The case should simply pop open into the 2 casing pieces and the screen mechanism. Warning. No Dot try to remove bottom casing until next step. Following the removal of the 6 screws, Locate the joint of the casing. Place a flat lever inside this crevice and apply pressure. The case should simply pop open into the 2 casing pieces and the screen mechanism. Warning. No Dot try to remove bottom casing until next step.
  • Following the removal of the 6 screws, Locate the joint of the casing. Place a flat lever inside this crevice and apply pressure. The case should simply pop open into the 2 casing pieces and the screen mechanism. Warning. No Dot try to remove bottom casing until next step.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
There are several components inside the casing. A board, a power cable, the screen and a ribbon cable. First, using tweezers lift the metallic clamp  connecting the ribbon to the board. WARNING. If the lever doesn't lift immediately, do not forcefully lift it. This could damage the  ribbon and board. When reapplying the ribbon, secure connection. There are several components inside the casing. A board, a power cable, the screen and a ribbon cable. First, using tweezers lift the metallic clamp  connecting the ribbon to the board. WARNING. If the lever doesn't lift immediately, do not forcefully lift it. This could damage the  ribbon and board. When reapplying the ribbon, secure connection. There are several components inside the casing. A board, a power cable, the screen and a ribbon cable. First, using tweezers lift the metallic clamp  connecting the ribbon to the board. WARNING. If the lever doesn't lift immediately, do not forcefully lift it. This could damage the  ribbon and board. When reapplying the ribbon, secure connection.
  • There are several components inside the casing. A board, a power cable, the screen and a ribbon cable. First, using tweezers lift the metallic clamp connecting the ribbon to the board. WARNING. If the lever doesn't lift immediately, do not forcefully lift it. This could damage the ribbon and board. When reapplying the ribbon, secure connection.

Ajouter un commentaire

Now that the ribbon is disconnected, remove the board carefully and place it aside. This piece still works so leave it attached to camera.
  • Now that the ribbon is disconnected, remove the board carefully and place it aside. This piece still works so leave it attached to camera.

Ajouter un commentaire

The screen is glued into the casing. Remove the screen by carefulyl lifting along the edges of the case until the screen pops out. Place new screen into the existing casing. A small about of glue or adhesive may be necessary if their isn't sufficient adhesive remaining in the case. Repeat steps in reverse to reapply screen. The screen is glued into the casing. Remove the screen by carefulyl lifting along the edges of the case until the screen pops out. Place new screen into the existing casing. A small about of glue or adhesive may be necessary if their isn't sufficient adhesive remaining in the case. Repeat steps in reverse to reapply screen.
  • The screen is glued into the casing. Remove the screen by carefulyl lifting along the edges of the case until the screen pops out. Place new screen into the existing casing. A small about of glue or adhesive may be necessary if their isn't sufficient adhesive remaining in the case. Repeat steps in reverse to reapply screen.

Ajouter un commentaire

If screen doesn't power on after replacing the battery, Go back and check connections of the ribbon.
  • If screen doesn't power on after replacing the battery, Go back and check connections of the ribbon.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Shane Riding

Membre depuis le 21/03/2018

748 Réputation

4 tutoriels rédigés

Équipe

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 4

7 derniers jours : 14

30 derniers jours : 26

Total : 45