Introduction

Please complete the dis-assembly guide before attempting to install new data ports, as it is a prerequisite.

Use this guide to replace a broken data port to get your USB and card readers back.

Remove the following two Phillips screws: Two 7.85 mm Phillips #1 screws
  • Remove the following two Phillips screws:

    • Two 7.85 mm Phillips #1 screws

Ajouter un commentaire

Pull the back cover off by lifting up on the cover.
  • Pull the back cover off by lifting up on the cover.

    • You may need to pull firmly as it requires quite a bit of force.

Ajouter un commentaire

Open the front tray.
  • Open the front tray.

Ajouter un commentaire

Lift the scanner compartment.
  • Lift the scanner compartment.

Ajouter un commentaire

After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.
  • After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.

Ajouter un commentaire

Push the blue lever back while twisting it clockwise in order to remove the lever from its slot. After removing the lever, close the scanner compartment and the scanner cover.
  • Push the blue lever back while twisting it clockwise in order to remove the lever from its slot.

  • After removing the lever, close the scanner compartment and the scanner cover.

Ajouter un commentaire

Use the plastic opening tool to pry open the side cover. Use the plastic opening tool to pry open the side cover.
  • Use the plastic opening tool to pry open the side cover.

Ajouter un commentaire

Flip the printer so that you are facing the underside. Use the plastic opening tool to remove the corner of the side panel from the pin.
  • Flip the printer so that you are facing the underside.

  • Use the plastic opening tool to remove the corner of the side panel from the pin.

    • Plastic pin.

Ajouter un commentaire

Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer. Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.
  • Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.

Ajouter un commentaire

Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture). Pry around the front and side edges for the easiest removal.
  • Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture).

    • Pry around the front and side edges for the easiest removal.

Ajouter un commentaire

After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.
  • After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.

Ajouter un commentaire

Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.
  • Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.

Ajouter un commentaire

Locate the buttons on the printer.
  • Locate the buttons on the printer.

Ajouter un commentaire

Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.
  • Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.

Ajouter un commentaire

Remove the following five Philips screws: Five 7.65 mm Philips #1 screws
  • Remove the following five Philips screws:

    • Five 7.65 mm Philips #1 screws

Ajouter un commentaire

Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture. Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.
  • Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.

Ajouter un commentaire

Remove the two screws using the Phillips #1 screwdriver. Two 7.8 mm Phillips #1 screws
  • Remove the two screws using the Phillips #1 screwdriver.

    • Two 7.8 mm Phillips #1 screws

Ajouter un commentaire

Gently pull the LCD screen up to remove it from its fixture.
  • Gently pull the LCD screen up to remove it from its fixture.

Ajouter un commentaire

Use the plastic opening tool to pry off the plastic button assembly.
  • Use the plastic opening tool to pry off the plastic button assembly.

Ajouter un commentaire

Gently pull the plastic button assembly up to remove it.
  • Gently pull the plastic button assembly up to remove it.

    • The plastic button assembly has a ribbon cable connected on the bottom, so make sure to be careful pulling it.

Ajouter un commentaire

Remove the ribbon cable connected to the backside of the plastic button assembly.
  • Remove the ribbon cable connected to the backside of the plastic button assembly.

Ajouter un commentaire

Remove the seven screws using the Phillips #1 screwdriver. Seven 8.7 mm Phillips #1 screws
  • Remove the seven screws using the Phillips #1 screwdriver.

    • Seven 8.7 mm Phillips #1 screws

Ajouter un commentaire

Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly.
  • Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly.

  • Gently lift the spring and pull the board out of its plastic button assembly.

Ajouter un commentaire

Remove the buttons from the plastic button assembly.
  • Remove the buttons from the plastic button assembly.

    • Buttons

Ajouter un commentaire

Remove the screw using the Phillips #1 screwdriver. 7.5 mm Phillips #1 screw
  • Remove the screw using the Phillips #1 screwdriver.

    • 7.5 mm Phillips #1 screw

Ajouter un commentaire

Remove the five screws using the Phillips #1 screwdriver. Five 3.5 mm Phillips #1 screws
  • Remove the five screws using the Phillips #1 screwdriver.

    • Five 3.5 mm Phillips #1 screws

Ajouter un commentaire

Remove the small plastic clip using the spudger.
  • Remove the small plastic clip using the spudger.

    • Small plastic clip

Ajouter un commentaire

Pull plastic inserts out of the holes in the top and bottom.
  • Pull plastic inserts out of the holes in the top and bottom.

    • Top and bottom plastic inserts

Ajouter un commentaire

Completely remove the board from the printer by pulling the board towards the back of the printer.
  • Completely remove the board from the printer by pulling the board towards the back of the printer.

    • This requires effort and time as the board comes out little by little.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Steven MacLean

Membre depuis le 14/01/2013

74 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 19-41, Regan Winter 2013 Membre de l'équipe Cal Poly, Team 19-41, Regan Winter 2013

CPSU-REGAN-W13S19G41

4 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 4

Total : 1,492