Introduction

This shows how to replace the LCD.

Pièces

Aucune pièce nécessaire.

Unscrew five Phillips screws using a #0 Phillips screwdriver. One screw is on upper right corner of the back panel.
  • Unscrew five Phillips screws using a #0 Phillips screwdriver.

  • One screw is on upper right corner of the back panel.

  • The other four screws are on the bottom of the camera.

Ajouter un commentaire

Open memory card cover by moving the slide switch toward the top end of of the camera.
  • Open memory card cover by moving the slide switch toward the top end of of the camera.

  • Remove the memory card from the slot.

Ajouter un commentaire

Remove the rear cover from the rest of the camera.
  • Remove the rear cover from the rest of the camera.

  • This may require gentle rocking of the case to free it.

Ajouter un commentaire

Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver. Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.
  • Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

Ajouter un commentaire

Free the front cover from the rest of the camera.
  • Free the front cover from the rest of the camera.

  • The cover may require gentle rocking to remove.

Ajouter un commentaire

Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.
  • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

Ajouter un commentaire

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Gently separate the top of LCD from the rest of the camera using your thumb.
  • Gently separate the top of LCD from the rest of the camera using your thumb.

  • Be careful not pull the LCD too far because of the ribbon cable connection.

  • Place the Spudger in the hole of the electrical ribbon.

  • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

  • The LCD will still be connected to the rest of the camera

Ajouter un commentaire

Unscrew single Phillips screw with a #0 Phillips screwdriver. Free the bottom panel and attached ribbon from the rest of the camera.
  • Unscrew single Phillips screw with a #0 Phillips screwdriver.

  • Free the bottom panel and attached ribbon from the rest of the camera.

  • Be careful not to damage the ribbon.

Ajouter un commentaire

Turn over the camera.
  • Turn over the camera.

  • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

  • The plastic will still be connected on the left side.

Ajouter un commentaire

Place the Spudger between the orange ribbon and the black ribbon gate.
  • Place the Spudger between the orange ribbon and the black ribbon gate.

  • Lift the ribbon gate using the Spudger.

Ajouter un commentaire

Place the Spludger in the corner of the ribbon above the hole.
  • Place the Spludger in the corner of the ribbon above the hole.

  • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

Ajouter un commentaire

Free this ribbon and the bottom panel from the rest of the camera.
  • Free this ribbon and the bottom panel from the rest of the camera.

  • Be careful not to damage the ribbon.

Ajouter un commentaire

Turn the camera over so you can see the LCD.
  • Turn the camera over so you can see the LCD.

  • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

Ajouter un commentaire

Lift the blue ribbon gate using the Spudger.
  • Lift the blue ribbon gate using the Spudger.

Ajouter un commentaire

Insert the Spudger into the hole of the ribbon.
  • Insert the Spudger into the hole of the ribbon.

  • Move the Spudger away from the gate to fully remove ribbon.

  • Be careful not to damage the ribbon.

Ajouter un commentaire

Lift the LCD away from the rest of the camera.
  • Lift the LCD away from the rest of the camera.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Nathan Balcom

Membre depuis le 21/01/2010

81 Réputation

8 tutoriels rédigés

Équipe

Cal Poly, Team 16-28, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 membres

9 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 1

Total : 2,848