Introduction

This guide will walk through the process of removing the button flex assembly from the camera.

Pièces

Aucune pièce nécessaire.

Open the battery compartment and remove the batteries.
  • Open the battery compartment and remove the batteries.

  • Remove the two screws that are deep in the battery compartment.

Ajouter un commentaire

Open the CF compartment and remove the top screw The panel, that holds the shutter button and zoom, will come off.
  • Open the CF compartment and remove the top screw

  • The panel, that holds the shutter button and zoom, will come off.

    • Be careful! There are two small wires connecting the speaker to the body of the camera. These are very delicate so proceed with caution. Do not remove.

Ajouter un commentaire

Unscrew the three small screws on the bottom.
  • Unscrew the three small screws on the bottom.

  • remove the wrist strap

Ajouter un commentaire

Remove the screw in the CF compartment.
  • Remove the screw in the CF compartment.

Ajouter un commentaire

Open the rubber Digital AV Out compartment flap. Pry the battery with the IFIXIT opening tool. Carefully pull out the battery with two fingers.
  • Open the rubber Digital AV Out compartment flap.

    • Pry the battery with the IFIXIT opening tool.

    • Carefully pull out the battery with two fingers.

      • Unscrew the two screws that are now visible.

Ajouter un commentaire

Starting from the bottom, carefully pull the casing off. The casing will now pivot at the top.
  • Starting from the bottom, carefully pull the casing off.

  • The casing will now pivot at the top.

    • There are three catches that hold the back casing to the body.

    • You may have to pull with some force. The rear panel will make a snapping noise when it separates from the body.

Ajouter un commentaire

The interior of the camera should look like this.
  • The interior of the camera should look like this.

Ajouter un commentaire

Remove the two screws at the top of the battery compartment.
  • Remove the two screws at the top of the battery compartment.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body. With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body.
  • With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body.

Ajouter un commentaire

After removing the front and rear panels, locate the viewfinder directly above the lens on top of the camera.
  • After removing the front and rear panels, locate the viewfinder directly above the lens on top of the camera.

  • Three screws hold the viewfinder in place. Two on the top and one on the lens side of the camera.

  • First, remove the screw in the bent corner of the viewfinder.

Ajouter un commentaire

Next, remove the 2nd screw directly across from the bent corner.  It may be hidden in the space under the orange circuitry.
  • Next, remove the 2nd screw directly across from the bent corner. It may be hidden in the space under the orange circuitry.

Ajouter un commentaire

Lastly, remove the final screw directly under the left side of the viewfinder (on the lens side).
  • Lastly, remove the final screw directly under the left side of the viewfinder (on the lens side).

Ajouter un commentaire

After removing the three screws, the only thing still holding the viewfinder in place is a small plastic peg.
  • After removing the three screws, the only thing still holding the viewfinder in place is a small plastic peg.

  • Remove the viewfinder with a firm pull directly upwards.

Ajouter un commentaire

Remove the two clearly visible screws from the control dial
  • Remove the two clearly visible screws from the control dial

  • The dial should come off easily

Ajouter un commentaire

You should be able to see the two small wires connecting the speaker to a small green plug With tweezers, carefully unplug the wires from the plug.  The wire should slide straight out
  • You should be able to see the two small wires connecting the speaker to a small green plug

    • With tweezers, carefully unplug the wires from the plug. The wire should slide straight out

  • Carefully replace the broken speaker/shutter panel with a new one

Ajouter un commentaire

The removed panel should look like this
  • The removed panel should look like this

Ajouter un commentaire

Remove the one visible screw that is attaching the flex assembly to the back of the camera.
  • Remove the one visible screw that is attaching the flex assembly to the back of the camera.

Ajouter un commentaire

Starting with the bottom-left corner (below the screen), lift the flex assembly away from the camera chassis. Starting with the bottom-left corner (below the screen), lift the flex assembly away from the camera chassis.
  • Starting with the bottom-left corner (below the screen), lift the flex assembly away from the camera chassis.

Ajouter un commentaire

Locate the small metal tab that attaches the flex assembly to the upper-right corner of the camera, and release it with a fingernail.
  • Locate the small metal tab that attaches the flex assembly to the upper-right corner of the camera, and release it with a fingernail.

    • The tab is very small and may be hard to see.

Ajouter un commentaire

Disconnect the black connector by lifting it up, as shown in the picture.
  • Disconnect the black connector by lifting it up, as shown in the picture.

    • Be careful, this is a difficult step. If you forcibly remove the flex assembly without disconnecting the connector, you may damage it.

Ajouter un commentaire

Gently pull the rest of the flex assembly away from the camera body until you reach the last connector.
  • Gently pull the rest of the flex assembly away from the camera body until you reach the last connector.

Ajouter un commentaire

Hold the flex assembly gently, but firmly, and pull it out of the connection with two fingers. Be sure to pull straight up, and not at an angle.
  • Hold the flex assembly gently, but firmly, and pull it out of the connection with two fingers.

    • Be sure to pull straight up, and not at an angle.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Brian

Membre depuis le 26/01/2010

69 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 14-40, Regan Winter 2010 Membre de l'équipe Cal Poly, Team 14-40, Regan Winter 2010

CPSU-REGAN-W10S14G40

5 membres

8 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 6

Total : 5,453