Flip the device over to the back side.
  • Flip the device over to the back side.

Ajouter un commentaire

Slide the small switch on the back to "MAIN".
  • Slide the small switch on the back to "MAIN".

Ajouter un commentaire

Slide the battery cover downwards.
  • Slide the battery cover downwards.

  • Pull off the battery cover.

Ajouter un commentaire

Pull the black tab to remove the battery.
  • Pull the black tab to remove the battery.

Ajouter un commentaire

Using the Phillips #00 screwdriver, remove the two screws near the top of the device.
  • Using the Phillips #00 screwdriver, remove the two screws near the top of the device.

Ajouter un commentaire

Using the Phillips #00 screwdriver, remove the two screws located inside the battery compartment.
  • Using the Phillips #00 screwdriver, remove the two screws located inside the battery compartment.

Ajouter un commentaire

Partially separate the two halves of the case by inserting the tip of a small flat head screw driver into the space between the halves.
  • Partially separate the two halves of the case by inserting the tip of a small flat head screw driver into the space between the halves.

Ajouter un commentaire

Pry the two halves of the case apart with the small flat head screwdriver.
  • Pry the two halves of the case apart with the small flat head screwdriver.

Ajouter un commentaire

Caution: be careful not to pull out the wires connecting the two halves of the outer case. These wires are necessary for the device to be able to function.
  • Caution: be careful not to pull out the wires connecting the two halves of the outer case. These wires are necessary for the device to be able to function.

  • Lay the two halves of the outer case next to the central components as shown.

Ajouter un commentaire

Using the #00 Phillips screwdriver, remove the screws from the corners of the screen. There are 3 screws total.
  • Using the #00 Phillips screwdriver, remove the screws from the corners of the screen. There are 3 screws total.

Ajouter un commentaire

Lift the tab on the motherboard and pull out the ribbon cable. After the ribbon cable is detached from the motherboard, the touch screen is completely separated from the device.
  • Lift the tab on the motherboard and pull out the ribbon cable.

  • After the ribbon cable is detached from the motherboard, the touch screen is completely separated from the device.

Ajouter un commentaire

Locate the small grey ribbon cable towards the bottom of the device. It should be located above the battery slot. Pinch both sides of the ribbon cable and pull it out.
  • Locate the small grey ribbon cable towards the bottom of the device. It should be located above the battery slot. Pinch both sides of the ribbon cable and pull it out.

Ajouter un commentaire

Locate the multicolored wire on the motherboard near the battery compartment. Pull on the wire by the base and lift to remove.
  • Locate the multicolored wire on the motherboard near the battery compartment. Pull on the wire by the base and lift to remove.

Ajouter un commentaire

Use the Phillips #00 Screwdriver to remove the two screws from the green circuit board on the back case.
  • Use the Phillips #00 Screwdriver to remove the two screws from the green circuit board on the back case.

Ajouter un commentaire

Remove the the three screws on the motherboard that are shown using the Phillips #00 Screwdriver.
  • Remove the the three screws on the motherboard that are shown using the Phillips #00 Screwdriver.

Ajouter un commentaire

Caution: do not break ribbon cables from the motherboard because this may cause damage to your device.
  • Caution: do not break ribbon cables from the motherboard because this may cause damage to your device.

  • Flip the motherboard towards the front cover to expose the ribbon cables underneath.

Ajouter un commentaire

Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second. Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second.
  • Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Ryan Fernandez

Membre depuis le 03/04/2012

47 Réputation

5 tutoriels rédigés

Équipe

Cal Poly, Team 5-4, Forte Spring 2012 Membre de l'équipe Cal Poly, Team 5-4, Forte Spring 2012

CPSU-FORTE-S12S5G4

6 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 6

Total : 770