Introduction

This guide will show you how to detach the lens assembly from the camera. You may have to repair or replace a cracked lens or one that won't retract.

Pièces

Aucune pièce nécessaire.

Locate 12 screws. Four on the left, four on the right, and four on the bottom. Locate 12 screws. Four on the left, four on the right, and four on the bottom. Locate 12 screws. Four on the left, four on the right, and four on the bottom.
  • Locate 12 screws. Four on the left, four on the right, and four on the bottom.

Ajouter un commentaire

Using the #00 Phillips screwdriver, remove the four 3.66mm screws from the bottom outer case, and the eight 1.75mm screw from the sides of the case.
  • Using the #00 Phillips screwdriver, remove the four 3.66mm screws from the bottom outer case, and the eight 1.75mm screw from the sides of the case.

Ajouter un commentaire

Separate the front case from the body of the camera.
  • Separate the front case from the body of the camera.

Ajouter un commentaire

Separate the back case from the body of the camera.
  • Separate the back case from the body of the camera.

Ajouter un commentaire

Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up. Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up. Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up.
  • Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up.

Ajouter un commentaire

Before removing the side metal bracket, first remove the attached strap knob by twisting it off.
  • Before removing the side metal bracket, first remove the attached strap knob by twisting it off.

  • Then, remove the side metal bracket by inserting the plastic opening tool under the bracket and pulling up.

Ajouter un commentaire

Using the plastic opening tool, pry up the LCD screen starting at one of the corners. Insert the tool under one of the corners and lift up.
  • Using the plastic opening tool, pry up the LCD screen starting at one of the corners. Insert the tool under one of the corners and lift up.

Ajouter un commentaire

Continue to lift the LCD screen all the way up. Be careful not to rip any wires connecting the LCD screen to the top of the camera.
  • Continue to lift the LCD screen all the way up.

  • Be careful not to rip any wires connecting the LCD screen to the top of the camera.

Ajouter un commentaire

Remove the orange ribbon cable by grabbing the white tab and pulling back. Remove the orange ribbon cable by grabbing the white tab and pulling back.
  • Remove the orange ribbon cable by grabbing the white tab and pulling back.

Ajouter un commentaire

Remove the two 1.66mm screws on both the bottom and top metal plates, using a #00 Phillips screwdriver. Remove the two 1.66mm screws on both the bottom and top metal plates, using a #00 Phillips screwdriver.
  • Remove the two 1.66mm screws on both the bottom and top metal plates, using a #00 Phillips screwdriver.

Ajouter un commentaire

Using the plastic opening tool, pry the battery case clamps (located on front of the camera) so that the bottom portion of the camera will come loose.
  • Using the plastic opening tool, pry the battery case clamps (located on front of the camera) so that the bottom portion of the camera will come loose.

Ajouter un commentaire

Once the bottom portion of the camera is removed, stand the camera  upright, bottom portion facing up, then detach the inner orange strip from the motherboard to the lens by inserting the plastic opening tool under the tab and lifting up.
  • Once the bottom portion of the camera is removed, stand the camera upright, bottom portion facing up, then detach the inner orange strip from the motherboard to the lens by inserting the plastic opening tool under the tab and lifting up.

Ajouter un commentaire

Fully remove the lens from the motherboard.
  • Fully remove the lens from the motherboard.

  • It will still be attached by wires and a different orange ribbon cable.

  • You can now proceed to repair the existing lens or replace it with a new lens.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Greg Bucher

Membre depuis le 19/04/2012

14 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 9-45, Regan Spring 2012 Membre de l'équipe Cal Poly, Team 9-45, Regan Spring 2012

CPSU-REGAN-S12S9G45

7 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 992