Pièces

Aucune pièce nécessaire.

Remove the four screws on the side of the speaker.
  • Remove the four screws on the side of the speaker.

Ajouter un commentaire

Remove the two back screws on the bottom of the camera.
  • Remove the two back screws on the bottom of the camera.

  • Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly.

Ajouter un commentaire

Remove the four screws on the side opposite of the speaker.
  • Remove the four screws on the side opposite of the speaker.

Ajouter un commentaire

Once all screws have been removed, gently pry open bottom casing. With tweezers, carefully remove ribbon from LCD screen.
  • Once all screws have been removed, gently pry open bottom casing.

  • With tweezers, carefully remove ribbon from LCD screen.

  • Set bottom casing aside.

Ajouter un commentaire

Gently pry apart the top casing using tweezers. Set the top casing aside. Set the top casing aside.
  • Gently pry apart the top casing using tweezers.

  • Set the top casing aside.

Ajouter un commentaire

Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.
  • Use tweezers or prongs to pry the LCD screen off from the opening.

  • Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

Ajouter un commentaire

Lift up the LCD screen, slowly move it to the other side. Lift up the LCD screen, slowly move it to the other side.
  • Lift up the LCD screen, slowly move it to the other side.

Ajouter un commentaire

Pry off the LCD casing. Pry off the LCD casing.
  • Pry off the LCD casing.

Ajouter un commentaire

Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera. Pull out the LCD screen with the ribbon from the camera.
  • Flip open the connector holding the ribbon.

  • Pull out the LCD screen with the ribbon from the camera.

Ajouter un commentaire

Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
  • Remove two screws on the side where the battery is located.

  • Remove the lanyard loop after the screws come off.

  • Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

Ajouter un commentaire

On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.
  • On the front of the camera near the flash flip the connector holding the ribbon.

  • Remove the ribbon from the connector.

Ajouter un commentaire

Carefully remove the L shaped frame from the camera. At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs.
  • Carefully remove the L shaped frame from the camera.

  • At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab.

  • Pop the frame off the bumps and tabs.

  • Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off.

Ajouter un commentaire

This is the flash assembly. It needs to be removed with soldering points circled.
  • This is the flash assembly.

  • It needs to be removed with soldering points circled.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Christian

Membre depuis le 28/01/2011

320 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team 4-38, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 4-38, Regan Winter 2011

CPSU-REGAN-W11S4G38

4 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 2,438