Introduction

If the crayon maker is not closing properly, check the position of the plastic arm. Adjust the plastic arm if it is out of place. Replace the arm if it is broken.

Pièces

Aucune pièce nécessaire.

Press the green arm away from the melting tray. Remove the melting tray. Pop the metal arms out of the green pivot support. Pop the metal arms out of the green pivot support.
  • Press the green arm away from the melting tray. Remove the melting tray.

  • Pop the metal arms out of the green pivot support.

Ajouter un commentaire

Remove the 2 screws (.75cm in length) currently securing the metal melting tray  with a Phillips #2 screwdriver. Remove the 2 screws (.75cm in length) currently securing the metal melting tray  with a Phillips #2 screwdriver. Remove the 2 screws (.75cm in length) currently securing the metal melting tray  with a Phillips #2 screwdriver.
  • Remove the 2 screws (.75cm in length) currently securing the metal melting tray with a Phillips #2 screwdriver.

Ajouter un commentaire

The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb. The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb. The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb.
  • The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb.

Ajouter un commentaire

Flip the crayon maker. Remove six screws (2 cm in length) with a spanner. Remove the green base plate and set it aside.
  • Flip the crayon maker.

  • Remove six screws (2 cm in length) with a spanner.

  • Remove the green base plate and set it aside.

Ajouter un commentaire

Locate the clear plastic arm inside the control box. Locate the clear plastic arm inside the control box. Locate the clear plastic arm inside the control box.
  • Locate the clear plastic arm inside the control box.

Ajouter un commentaire

If necessary, unscrew the plastic arm with a Phillips #00 Precision screwdriver and readjust the arm until the desired position is reached. If the plastic arm is broken, contact Crayola for replacement parts.
  • If necessary, unscrew the plastic arm with a Phillips #00 Precision screwdriver and readjust the arm until the desired position is reached.

  • If the plastic arm is broken, contact Crayola for replacement parts.

Ajouter un commentaire

Remove the green base from the crayon maker and set aside. Locate the clear box. Locate the clear box.
  • Remove the green base from the crayon maker and set aside.

  • Locate the clear box.

Ajouter un commentaire

There are four screws (circled in red) that need to be removed with a Phillips #00 Precision screwdriver. There are four screws (circled in red) that need to be removed with a Phillips #00 Precision screwdriver.
  • There are four screws (circled in red) that need to be removed with a Phillips #00 Precision screwdriver.

Ajouter un commentaire

Remove five screws (1.5 cm in length) using a Phillips #00 Precision screwdriver and open the clear plastic box.
  • Remove five screws (1.5 cm in length) using a Phillips #00 Precision screwdriver and open the clear plastic box.

Ajouter un commentaire

The plastic arm should be positioned as shown in the figure. Adjust the arm's position if necessary.
  • The plastic arm should be positioned as shown in the figure. Adjust the arm's position if necessary.

  • If the plastic arm is broken, contact Crayola for a replacement arm.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Melissa

Membre depuis le 10/10/2014

210 Réputation

2 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 3

Total : 421