Introduction

Follow the remaining steps in this guide in order to locate and replace the speakers locate on the interior bottom of the device housing. Take care not to confuse the speakers with batteries, as they look similar.

Flip the device and lay flat.
  • Flip the device and lay flat.

Ajouter un commentaire

Remove the four (9 mm) screws with a PH2 screwdriver.
  • Remove the four (9 mm) screws with a PH2 screwdriver.

  • Remove the two (7 mm) located with a PH2 screwdriver.

Ajouter un commentaire

Flip the device over and pry the top off with a plastic opening tool. Flip the device over and pry the top off with a plastic opening tool. Flip the device over and pry the top off with a plastic opening tool.
  • Flip the device over and pry the top off with a plastic opening tool.

Ajouter un commentaire

Remove the ribbon cable connecting the motherboard to the button control board by gently pulling it from its connector.
  • Remove the ribbon cable connecting the motherboard to the button control board by gently pulling it from its connector.

Ajouter un commentaire

Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver. Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver.
  • Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver.

Ajouter un commentaire

Remove the two cables connected to the motherboard: black power cable and the red/black fan cable. the black cable requires more force to remove than the other cables. the black cable requires more force to remove than the other cables.
  • Remove the two cables connected to the motherboard: black power cable and the red/black fan cable.

  • the black cable requires more force to remove than the other cables.

Ajouter un commentaire

Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard. Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard.
  • Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard.

Ajouter un commentaire

Raise motherboard by lifting sideways and then up to avoid the ports.
  • Raise motherboard by lifting sideways and then up to avoid the ports.

Ajouter un commentaire

Remove wires attaching the piezoelectric speakers to the motherboard. Remove wires attaching the piezoelectric speakers to the motherboard.
  • Remove wires attaching the piezoelectric speakers to the motherboard.

Ajouter un commentaire

Remove the five screws securing the black plastic cover with a J0 screwdriver. Lift up and out to remove.
  • Remove the five screws securing the black plastic cover with a J0 screwdriver.

  • Lift up and out to remove.

Ajouter un commentaire

Remove the two (3 mm) screws connecting the bracket down and pull out the reflector, using a  J0 Philips Head Screwdriver. Remove the two (3 mm) screws connecting the bracket down and pull out the reflector, using a  J0 Philips Head Screwdriver.
  • Remove the two (3 mm) screws connecting the bracket down and pull out the reflector, using a J0 Philips Head Screwdriver.

Ajouter un commentaire

Slide the mirror straight up to remove. Slide the mirror straight up to remove. Slide the mirror straight up to remove.
  • Slide the mirror straight up to remove.

Ajouter un commentaire

Slide out the power source and disconnect its cables from the power jack and the light. Slide out the power source and disconnect its cables from the power jack and the light. Slide out the power source and disconnect its cables from the power jack and the light.
  • Slide out the power source and disconnect its cables from the power jack and the light.

Ajouter un commentaire

Remove the screws holding down the first speaker with a J0 screwdriver. Remove the screws holding down the second speaker down. Remove the screws holding down the second speaker down.
  • Remove the screws holding down the first speaker with a J0 screwdriver.

  • Remove the screws holding down the second speaker down.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Ryan Goldin

Membre depuis le 15/02/2018

210 Réputation

1 tutoriel rédigé

Équipe

USF Tampa, Team S16-G2, Boczar Spring 2018 Membre de l'équipe USF Tampa, Team S16-G2, Boczar Spring 2018

USFT-BOCZAR-S18S16G2

5 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 11

Total : 64