Introduction

This guide to remove your Dell Inspiron 13-7359 screen. You will need a phillips #0 screwdriver and a small plastic spudger. This guide will require more time and is more difficult than the other replacement guides.

First flip over the laptop to expose the back panel
  • First flip over the laptop to expose the back panel

  • Use a Phillips #0 screwdriver to unscrew all ten 7mm Phillips head screws holding the back panel in place.

Ajouter un commentaire

With a plastic spudger, carefully remove the back panel by prying each corner off individually
  • With a plastic spudger, carefully remove the back panel by prying each corner off individually

  • Slowly pick up the panel and set it aside

Ajouter un commentaire

The battery will be the largest black component in the device located near the bottom edge. Using a Phillips #0 screwdriver, unscrew the two 3mm Phillips head screws holding in the battery. The battery will be the largest black component in the device located near the bottom edge. Using a Phillips #0 screwdriver, unscrew the two 3mm Phillips head screws holding in the battery. The battery will be the largest black component in the device located near the bottom edge. Using a Phillips #0 screwdriver, unscrew the two 3mm Phillips head screws holding in the battery.
  • The battery will be the largest black component in the device located near the bottom edge. Using a Phillips #0 screwdriver, unscrew the two 3mm Phillips head screws holding in the battery.

Ajouter un commentaire

To remove the old battery, slightly lift the bottom edge of the battery with your hands Now slowly pull the battery towards you to fully detach the battery Now slowly pull the battery towards you to fully detach the battery
  • To remove the old battery, slightly lift the bottom edge of the battery with your hands

  • Now slowly pull the battery towards you to fully detach the battery

Ajouter un commentaire

Unscrew and remove the 2 of the 3mm Phillips head screws holding the hard drive in place.
  • Unscrew and remove the 2 of the 3mm Phillips head screws holding the hard drive in place.

Ajouter un commentaire

Lift and hold the hard drive in your left hand. Use your right hand to grab hold of the black wire connector attached on the right of the hard drive.
  • Lift and hold the hard drive in your left hand.

  • Use your right hand to grab hold of the black wire connector attached on the right of the hard drive.

  • Carefully pull the connector away from the hard drive to completely disconnect from the laptop.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Unscrew and remove the 2 of the 7mm Phillips head screws holding the cooling fan in place. Unscrew and remove the 2 of the 7mm Phillips head screws holding the cooling fan in place.
  • Unscrew and remove the 2 of the 7mm Phillips head screws holding the cooling fan in place.

Ajouter un commentaire

Hold the cooling fan with one hand.
  • Hold the cooling fan with one hand.

  • With the other hand, grab hold of the part of the copper heat sink that is attached to the cooling fan.

  • Carefully pull the cooling fan away from the attached part so that it becomes fully disconnected.

Ajouter un commentaire

Make sure that the Battery, Hard Drive, and Cooling Fan are safely removed.
  • Make sure that the Battery, Hard Drive, and Cooling Fan are safely removed.

Ajouter un commentaire

Unplug antenna cables located at the top left corner. Unplug daughter board located to the bottom left of the cooling fan.
  • Unplug antenna cables located at the top left corner.

  • Unplug daughter board located to the bottom left of the cooling fan.

Ajouter un commentaire

Find the heat sink (copper colored metal). Use Phillips 0 screwdriver to loosen the 3 of the 3mm Phillips head screws from the heat sink.
  • Find the heat sink (copper colored metal).

  • Use Phillips 0 screwdriver to loosen the 3 of the 3mm Phillips head screws from the heat sink.

  • Remove the heat sink

Ajouter un commentaire

Use Phillips 0 screwdriver to unscrew the 2 of the 3mm screws holding the LCD cable bracket in place. Remove the LCD cable bracket. Unplug LCD and touchscreen cables.
  • Use Phillips 0 screwdriver to unscrew the 2 of the 3mm screws holding the LCD cable bracket in place.

  • Remove the LCD cable bracket.

  • Unplug LCD and touchscreen cables.

Ajouter un commentaire

Use Phillips 0 screwdriver to unscrew and remove the 3 of the 7mm screws from the LCD display. Open the laptop so that the screen and keyboard are face down on the desk. Carefully disconnect the LCD display by lifting the screen upward and away from the bottom half of the laptop.
  • Use Phillips 0 screwdriver to unscrew and remove the 3 of the 7mm screws from the LCD display.

  • Open the laptop so that the screen and keyboard are face down on the desk.

  • Carefully disconnect the LCD display by lifting the screen upward and away from the bottom half of the laptop.

Ajouter un commentaire

Using a plastic spudger carefully separate the casing of the screen. Using a plastic spudger carefully separate the casing of the screen.
  • Using a plastic spudger carefully separate the casing of the screen.

Ajouter un commentaire

Use the plastic spudger to disconnect the mini circuit board from the casing. Disconnect the small wires connecting the screen to the casing. Disconnect the small wires connecting the screen to the casing.
  • Use the plastic spudger to disconnect the mini circuit board from the casing.

  • Disconnect the small wires connecting the screen to the casing.

Ajouter un commentaire

Remove the loose wiring from the perimeter of the screen. Gently separate the LCD screen from the laptop casing.
  • Remove the loose wiring from the perimeter of the screen.

  • Gently separate the LCD screen from the laptop casing.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Austin Navarro

Membre depuis le 30/01/2018

172 Réputation

1 tutoriel rédigé

Équipe

Baylor, Team S1-G6, Johnson Spring 2018 Membre de l'équipe Baylor, Team S1-G6, Johnson Spring 2018

BU-JOHNSON-S18S1G6

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 12

30 derniers jours : 71

Total : 163