Introduction

This guide will show you how to open the outer shell of your Flip Video.

Pièces

Aucune pièce nécessaire.

Turn off the device and take the batteries out. Remove metal sticker under the LCD screen with a spudger.
  • Turn off the device and take the batteries out.

  • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

Ajouter un commentaire

Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.
  • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

Ajouter un commentaire

Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell. Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.
  • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

Ajouter un commentaire

Open battery door. This can be done by gently depressing and sliding the battery down downward.
  • Open battery door. This can be done by gently depressing and sliding the battery down downward.

Ajouter un commentaire

Use the spudger to separate outer shells.
  • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

Ajouter un commentaire

Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.
  • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

Ajouter un commentaire

Slowly lift the left side of the circuit board.
  • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

Ajouter un commentaire

Disconnect the USB port cable from the back side of the circuit board.
  • Disconnect the USB port cable from the back side of the circuit board.

Ajouter un commentaire

Slide out the battery contacts.
  • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

Ajouter un commentaire

Remove black 3mm screw that secures wire to outer shell with #00 Phillips screwdriver.
  • Remove black 3mm screw that secures wire to outer shell with #00 Phillips screwdriver.

Ajouter un commentaire

Lift wire out of the outer shell slot.
  • Lift wire out of the outer shell slot.

    • The wire mount should stay attached to the wire.

Ajouter un commentaire

Use tweezers to remove the spring that holds the port door shut.
  • Use tweezers to remove the spring that holds the port door shut.

    • Make sure the spring is firmly grasped by the tweezers so that it does not shoot off of the case.

Ajouter un commentaire

Remove the 3 screws securing USB port cover to the outer case with the #00 Phillips screwdriver.
  • Remove the 3 screws securing USB port cover to the outer case with the #00 Phillips screwdriver.

Ajouter un commentaire

Remove the USB port cover.
  • Remove the USB port cover.

Ajouter un commentaire

Remove the USB slider.
  • Remove the USB slider.

Ajouter un commentaire

Lift out the USB port slowly.
  • Lift out the USB port slowly.

    • Since the hinge is spring loaded, be careful that no pieces fall out when the port is lifted.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Elizabeth

Membre depuis le 15/04/2010

100 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 26-21, Regan Spring 2010 Membre de l'équipe Cal Poly, Team 26-21, Regan Spring 2010

CPSU-REGAN-S10S26G21

4 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 3

Total : 3,894