Introduction

This guide will show you how to remove the main camera lens assembly from the camera's frame.

Remove the following screws: Two silver 3.15mm Phillips #00 screws on the right side of the camera
  • Remove the following screws:

    • Two silver 3.15mm Phillips #00 screws on the right side of the camera

    • Two silver 2.08mm Phillips #00 screws on the left side of the camera

Ajouter un commentaire

Remove the two indicated screws on the bottom of the camera:
  • Remove the two indicated screws on the bottom of the camera:

    • The screw circled in red is a longer silver 3.15mm Phillips #00 screw

    • The screw circled in blue is a shorter silver 2.25mm Phillips #00 screw

Ajouter un commentaire

Carefully pull the back of casing away from the front. Carefully pull the back of casing away from the front.
  • Carefully pull the back of casing away from the front.

Ajouter un commentaire

After removing the back cover, several things must be removed. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.
  • After removing the back cover, several things must be removed.

  • Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.

Ajouter un commentaire

To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off. To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.
  • To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.

Ajouter un commentaire

On the front of the camera, in battery case, remove screws indicated: Two black 2.05mm Phillips #00 screws
  • On the front of the camera, in battery case, remove screws indicated:

    • Two black 2.05mm Phillips #00 screws

Ajouter un commentaire

Flip the camera over to the backside and remove screws indicated: The screw circled in red is a longer black 3.00mm Phillips #00 screw
  • Flip the camera over to the backside and remove screws indicated:

    • The screw circled in red is a longer black 3.00mm Phillips #00 screw

    • The screw circled in red is a shorter black 2.00mm Phillips #00 screw

Ajouter un commentaire

Pull the cover plate off for the two power cord jacks.
  • Pull the cover plate off for the two power cord jacks.

Ajouter un commentaire

Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.
  • Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.

Ajouter un commentaire

Remove the orange tape on top of the SD cardholder.
  • Remove the orange tape on top of the SD cardholder.

Ajouter un commentaire

Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off.
  • Open the battery cover and lift plastic piece off.

Ajouter un commentaire

Remove tape on left side of camera.
  • Remove tape on left side of camera.

Ajouter un commentaire

Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.
  • Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.

Ajouter un commentaire

Remove top left LCD bracket.
  • Remove top left LCD bracket.

  • This is a small piece, be careful not to lose it.

Ajouter un commentaire

Push down bottom left LCD bracket to release the LCD from grip. Push down bottom left LCD bracket to release the LCD from grip.
  • Push down bottom left LCD bracket to release the LCD from grip.

Ajouter un commentaire

Gently lift up LCD screen.
  • Gently lift up LCD screen.

Ajouter un commentaire

Slowly pull LCD screen to the left to remove it from the other grips. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.
  • Slowly pull LCD screen to the left to remove it from the other grips.

  • BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.

Ajouter un commentaire

Lift up tape slightly on both sides of speaker. Lift up tape slightly on both sides of speaker. Lift up tape slightly on both sides of speaker.
  • Lift up tape slightly on both sides of speaker.

Ajouter un commentaire

Use the pointed end of a spudger to lift up brackets. Lift speaker cover out. Lift speaker cover out.
  • Use the pointed end of a spudger to lift up brackets.

  • Lift speaker cover out.

Ajouter un commentaire

Remove speaker cover.
  • Remove speaker cover.

Ajouter un commentaire

Turn camera to front. Carefully peel off orange wire tape. The tape is glued to the surface indicated.
  • Turn camera to front.

  • Carefully peel off orange wire tape. The tape is glued to the surface indicated.

  • Lift speaker from holder.

Ajouter un commentaire

Use a wedge to lift up the wire tape flap. Use a wedge to lift up the wire tape flap.
  • Use a wedge to lift up the wire tape flap.

Ajouter un commentaire

Insert the point of a spudger underneath the wire shown. Insert the point of a spudger underneath the wire shown. Insert the point of a spudger underneath the wire shown.
  • Insert the point of a spudger underneath the wire shown.

Ajouter un commentaire

Carefully lift the wire out of the crevasses. Carefully lift the wire out of the crevasses.
  • Carefully lift the wire out of the crevasses.

Ajouter un commentaire

Slowly bend the speaker's wire tape away from the lens assembly.  Avoid creasing the tape.
  • Slowly bend the speaker's wire tape away from the lens assembly. Avoid creasing the tape.

Ajouter un commentaire

Remove indicated screws: Three Black 3.80mm Phillips #00 screws. Three Black 3.80mm Phillips #00 screws.
  • Remove indicated screws:

    • Three Black 3.80mm Phillips #00 screws.

Ajouter un commentaire

Remove the indicated black 3.40mm Phillips #00 screw on the bottom of the camera. Remove copper leads.
  • Remove the indicated black 3.40mm Phillips #00 screw on the bottom of the camera.

  • Remove copper leads.

Ajouter un commentaire

Unscrew the indicated 3.80mm Phillips #00 screw on the back of the camera. Remove screw and bracket. Remove screw and bracket.
  • Unscrew the indicated 3.80mm Phillips #00 screw on the back of the camera.

  • Remove screw and bracket.

Ajouter un commentaire

Turn the camera over to the front.
  • Turn the camera over to the front.

  • In the following step, you will undo the indicated pegs. PROCEED TO THE NEXT STEP.

Ajouter un commentaire

Carefully holding the camera, grab the corresponding two points. Carefully twist the lens assembly away from you. You will be turning your hand clockwise. Pull lens assembly out.
  • Carefully holding the camera, grab the corresponding two points.

  • Carefully twist the lens assembly away from you. You will be turning your hand clockwise.

  • Pull lens assembly out.

  • The lens assembly is attached to the logic board by wire tape.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Bassem Tossoun

Membre depuis le 21/01/2011

201 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 4-29, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 4-29, Regan Winter 2011

CPSU-REGAN-W11S4G29

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 4

Total : 1,475