Introduction

We will disassemble the camera case so that internal components can be accessed.

Pièces

Aucune pièce nécessaire.

Use the Phillips head screwdriver, rotating counterclockwise, to remove the two screws at the bottom of the camera. Set screws aside.
  • Use the Phillips head screwdriver, rotating counterclockwise, to remove the two screws at the bottom of the camera. Set screws aside.

Ajouter un commentaire

Hold the camera right side up with the LCD screen facing you. There is a rubber cover on the left side of the camera. Move the cover out of the way to expose another screw. Use a Phillips head screwdriver, rotating counterclockwise, to remove both screws.  Set the screws aside.
  • Hold the camera right side up with the LCD screen facing you. There is a rubber cover on the left side of the camera. Move the cover out of the way to expose another screw.

  • Use a Phillips head screwdriver, rotating counterclockwise, to remove both screws. Set the screws aside.

Ajouter un commentaire

Hold the camera right side up with the LCD screen facing you. Open the battery on the right side of the camera casing by pushing slightly in the direction of the arrow. Note: You may see a memory card. If so, remove the card by pushing down on it and it will come loose so you can gently pull it out.
  • Hold the camera right side up with the LCD screen facing you. Open the battery on the right side of the camera casing by pushing slightly in the direction of the arrow.

  • Note: You may see a memory card. If so, remove the card by pushing down on it and it will come loose so you can gently pull it out.

  • Use the Phillips head screwdriver, rotating counterclockwise, to remove the two screws on either side of the memory card. Set the screws aside.

Ajouter un commentaire

While pulling the grey tab towards the back of the camera, lift the black section of the battery cover up. Use the Phillips head screwdriver, rotating counter clockwise to remove the two screws on either side of the battery slots and set them aside.
  • While pulling the grey tab towards the back of the camera, lift the black section of the battery cover up.

  • Use the Phillips head screwdriver, rotating counter clockwise to remove the two screws on either side of the battery slots and set them aside.

  • When reassembling the camera, make sure that the grey part of the battery cover is underneath the two halves of the camera casing. The black cover should fit over the empty space where the batteries go and the holes for the screws should line up with the holes in the casing. You may need to pull the green part of the inside of the camera away from the grey tab in order to move the battery cover into place.

Ajouter un commentaire

Hold the camera right side up with the LCD screen facing you.  Remove the screen battery located to the left of the screen. Set it aside. Hold the camera right side up with the LCD screen facing you.  Remove the screen battery located to the left of the screen. Set it aside.
  • Hold the camera right side up with the LCD screen facing you. Remove the screen battery located to the left of the screen. Set it aside.

Ajouter un commentaire

Be cautious when completing this step, as the camera will only be held together by two short ribbons. Gently pull the camera apart, and be aware that the ribbons are at the bottom of the camera.
  • Be cautious when completing this step, as the camera will only be held together by two short ribbons.

  • Gently pull the camera apart, and be aware that the ribbons are at the bottom of the camera.

Ajouter un commentaire

On the front half of the camera, locate the black tabs on either side of the white ribbon. Use the metal tweezers to gently move the black tabs away from the eye viewing lens.
  • On the front half of the camera, locate the black tabs on either side of the white ribbon.

  • Use the metal tweezers to gently move the black tabs away from the eye viewing lens.

  • Gently pull the white ribbon out of the connection.

Ajouter un commentaire

On the front half of the camera, locate the black tabs on either side of the orange ribbon. Use the metal tweezers to gently move the black tabs away from the eye viewing lens. Gently pull the orange ribbon out of the connection.
  • On the front half of the camera, locate the black tabs on either side of the orange ribbon.

  • Use the metal tweezers to gently move the black tabs away from the eye viewing lens.

  • Gently pull the orange ribbon out of the connection.

  • Note: Your camera should now be in two separate pieces. You can set aside the half with the LCD screen.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Daniel Stone

Membre depuis le 28/01/2011

101 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 7-37, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 7-37, Regan Winter 2011

CPSU-REGAN-W11S7G37

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 3

Total : 352