Réparez vos affaires Communauté Boutique

Disassembling the Linksys E1200

Introduction

Multiple parts can easily break during disassembly. Proceed slowly with caution to avoid problems.

Ce dont vous avez besoin

  1. Disassembling the Linksys E1200, Cover and Circuit Board: étape 1, image 1 de 3 Disassembling the Linksys E1200, Cover and Circuit Board: étape 1, image 2 de 3 Disassembling the Linksys E1200, Cover and Circuit Board: étape 1, image 3 de 3

    • Opening the device will void your warranty.

    • Anti-slip pads cover three screws that hold the device together. Pry off the pads to access the screws.

    • Remove the three screws.

    • Save the pads for reassembly.

    Traduire

  2. Disassembling the Linksys E1200: étape 2, image 1 de 3 Disassembling the Linksys E1200: étape 2, image 2 de 3 Disassembling the Linksys E1200: étape 2, image 3 de 3

    • Once the three screws are removed, the device is ready for disassembly.

    • Push up on the rear flap while holding down on the rest of the body. This will open a small gap.

    • Insert the plastic opening tool in the gap and begin prying on the corner.

    • Continue to pry around the body of the case. Separate both sides of the case with this method.

    Traduire

  4. Disassembling the Linksys E1200: étape 3, image 1 de 2 Disassembling the Linksys E1200: étape 3, image 2 de 2

    • Once the sides are released, the front of the cover can be removed.

    • Use a plastic opening tool to separate the front of the cover from the body.

    • It is helpful to use a different plastic opening tool as a wedge on the sides to prevent them from snapping back together.

    Traduire

  5. Disassembling the Linksys E1200: étape 4, image 1 de 3 Disassembling the Linksys E1200: étape 4, image 2 de 3 Disassembling the Linksys E1200: étape 4, image 3 de 3

    • The cover can now be removed.

    • To repair anything on the circuit board, use the plastic opening tool to pull back on the two tabs holding it down.

    • Use caution when pulling on the tabs as they are stiff and easy to break.

    • Keep the tabs if they snap off. The tabs can be reattached with glue when reassembling the device.

    Traduire

  6. Disassembling the Linksys E1200: étape 5, image 1 de 3 Disassembling the Linksys E1200: étape 5, image 2 de 3 Disassembling the Linksys E1200: étape 5, image 3 de 3

    • If the antenna needs to be disconnected, desolder the connection and reattach it prior to reassembly.

    • If the ethernet ports, power port, or reset button are damaged, the large solder points allow you to replace them.

    • Many components on the board cannot be serviced. These components were attached by a machine and cannot be removed.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

13 autres ont terminé cette réparation.

Auteur

avec 10 autres contributeurs

Tahisha Hicks

Membre depuis le 02/24/14

409 Réputation

4 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Michigan Tech, Team 5-4, Lauer Spring 2014 Membre de l'équipe Michigan Tech, Team 5-4, Lauer Spring 2014

MTU-LAUER-S14S5G4

3 membres

7 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 1

30 derniers jours : 7

Total : 7,024