Introduction

Displays can get easily damaged either with time, or with any liquids or impacts.

Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.
  • Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.

  • Turn over laptop so that the bottom is showing.

  • Unlock the latch.

Ajouter un commentaire

Remove the back cover and you will then be able to see the battery.
  • Remove the back cover and you will then be able to see the battery.

Ajouter un commentaire

Unlatch the two latches securing the battery in the case.
  • Unlatch the two latches securing the battery in the case.

Ajouter un commentaire

Use the blue opening tool to lift and remove the battery.
  • Use the blue opening tool to lift and remove the battery.

Ajouter un commentaire

Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.
  • Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.

Ajouter un commentaire

Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.
  • Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.

  • Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.

Ajouter un commentaire

Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.
  • Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.

  • Remove SD card cap by just sliding out to reveal one screw.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.
  • Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.

  • Remove the 4mm SD card screw using the J00 tip.

Ajouter un commentaire

Remove the one 4mm fan screw using the J00 tip screwdriver.
  • Remove the one 4mm fan screw using the J00 tip screwdriver.

  • Remove screw and metal plate to expose ribbon cable connector.

Ajouter un commentaire

Use an opening tool to pry up the ribbon connector to disconnect.
  • Use an opening tool to pry up the ribbon connector to disconnect.

Ajouter un commentaire

Turn laptop over back to normal position as shown in the image.
  • Turn laptop over back to normal position as shown in the image.

  • Use opening tools to pry up keyboard.

  • When prying up keyboard, be sure to start near any corner of the keyboard.

  • There are two ribbon cables that must be disconnected before fully removing keyboard.

Ajouter un commentaire

Carefully lift keyboard on one side to expose the two ribbon cables. Use an opening tool to lift up the locking clip and unplug the two ribbon cables. Use an opening tool to lift up the locking clip and unplug the two ribbon cables.
  • Carefully lift keyboard on one side to expose the two ribbon cables.

  • Use an opening tool to lift up the locking clip and unplug the two ribbon cables.

Ajouter un commentaire

Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.
  • Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.

Ajouter un commentaire

Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily. The display is connected to the shell of the laptop. The display is connected to the shell of the laptop.
  • Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.

  • The display is connected to the shell of the laptop.

Ajouter un commentaire

Unplug fan cable by pulling away from its connector.
  • Unplug fan cable by pulling away from its connector.

Ajouter un commentaire

Unscrew the two 6mm fan screws using the J00 tip.
  • Unscrew the two 6mm fan screws using the J00 tip.

  • Fan screws are encased in springs and cannot be removed.

Ajouter un commentaire

Retrieve the monitor display connected to the plastic chassis.
  • Retrieve the monitor display connected to the plastic chassis.

Ajouter un commentaire

Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.
  • Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.

Ajouter un commentaire

Unhinge the monitor display from the chassis.
  • Unhinge the monitor display from the chassis.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Alberto Carlos Perez

Membre depuis le 14/02/2018

293 Réputation

2 tutoriels rédigés

Équipe

USF Tampa, Team S5-G1, Eyestone Spring 2018 Membre de l'équipe USF Tampa, Team S5-G1, Eyestone Spring 2018

USFT-EYESTONE-S18S5G1

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 6

30 derniers jours : 21

Total : 59