Press each thumb on both sides of the upper corners and apply pressure downwards. Then, while still applying pressure, slide the back cover down.
  • Press each thumb on both sides of the upper corners and apply pressure downwards.

  • Then, while still applying pressure, slide the back cover down.

Ajouter un commentaire

Remove the Battery. Remove the SIM card.
  • Remove the Battery.

  • Remove the SIM card.

Ajouter un commentaire

Push the SD card in and the SD card should pop loose.
  • Push the SD card in and the SD card should pop loose.

  • Pull the SD card out.

Ajouter un commentaire

Remove the four 6-mm T5 torx screws in the four corners. Remove the two 4-mm T5 torx screws in the middle.
  • Remove the four 6-mm T5 torx screws in the four corners.

  • Remove the two 4-mm T5 torx screws in the middle.

Ajouter un commentaire

Use the existing gap, to dislodge the antenna cover from the phone. Pull out the antenna cover to have access to the motherboard.
  • Use the existing gap, to dislodge the antenna cover from the phone.

  • Pull out the antenna cover to have access to the motherboard.

Ajouter un commentaire

Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward. Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.
  • Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward.

  • Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.

Ajouter un commentaire

Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone. Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.
  • Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone.

  • Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.

  • Do not remove any of the screws located on the actual circuit boards.

Ajouter un commentaire

Place a finger between the circuit board and the front cover, and lift up gently. Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach. Finish separating the circuit board from the front panel.
  • Place a finger between the circuit board and the front cover, and lift up gently.

  • Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach.

  • Finish separating the circuit board from the front panel.

Ajouter un commentaire

After following the prerequisite guide listed above, the phone should have the circuit board housing group on one piece.
  • After following the prerequisite guide listed above, the phone should have the circuit board housing group on one piece.

  • The front cover and screen of the phone should be located on the other piece.

Ajouter un commentaire

Place a finger on the front side of the screen, and push up as indicated. Carefully grab onto the sides of the LCD and glass screen.
  • Place a finger on the front side of the screen, and push up as indicated.

  • Carefully grab onto the sides of the LCD and glass screen.

  • Continue to angle the LCD and glass screen further up.

Ajouter un commentaire

Carefully lift the screen away from the front cover.
  • Carefully lift the screen away from the front cover.

  • The adhesive should be easy to separate while separating the front cover from the screen.

Ajouter un commentaire

Change old LCD and glass digitizer with a replacement.
  • Change old LCD and glass digitizer with a replacement.

  • The LCD and glass digitizer can be separated by disconnecting the ribbon cable, and separating the layer of the LCD from the glass screen.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Tony Tran

Membre depuis le 25/09/2012

351 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team 2-9, Propen Fall 2012 Membre de l'équipe Cal Poly, Team 2-9, Propen Fall 2012

CPSU-PROPEN-F12S2G9

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 2

Total : 2,710