Introduction

Remove and replace the microphone built into the TC-580 circuit board. This will require soldering that could permanently damage the circuit board of your radio so please consider other options for repair. This repair is for users that can't have other parties hear them on the radio.

Remove the two 10mm Phillips #0 from the belt clip. Remove the two 10mm Phillips #0 from the belt clip.
  • Remove the two 10mm Phillips #0 from the belt clip.

Ajouter un commentaire

Push in the release button and pull up on the battery to remove. Push in the release button and pull up on the battery to remove.
  • Push in the release button and pull up on the battery to remove.

Ajouter un commentaire

Twist antenna counter-clockwise and set damaged antenna  aside.
  • Twist antenna counter-clockwise and set damaged antenna aside.

Ajouter un commentaire

Remove the volume knob by firmly lifting up on both sides of it.
  • Remove the volume knob by firmly lifting up on both sides of it.

Ajouter un commentaire

Remove the orange o-ring around volume knob using tweezers.
  • Remove the orange o-ring around volume knob using tweezers.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Remove grey nut from base of volume knob by turning it counterclockwise  with a set of tweezers.
  • Remove grey nut from base of volume knob by turning it counterclockwise with a set of tweezers.

Ajouter un commentaire

Remove the brass washer from the base of the antenna slot by turning it counterclockwise with a set of tweezers.
  • Remove the brass washer from the base of the antenna slot by turning it counterclockwise with a set of tweezers.

Ajouter un commentaire

Remove the two 15mm T8 Torx screws from the base of the battery cavity. Remove the two 15mm T8 Torx screws from the base of the battery cavity.
  • Remove the two 15mm T8 Torx screws from the base of the battery cavity.

Ajouter un commentaire

Using a plastic opening tool, pry in between the plastic case and metal circuit board to remove the board.
  • Using a plastic opening tool, pry in between the plastic case and metal circuit board to remove the board.

Ajouter un commentaire

Peel off the keypad by hand.
  • Peel off the keypad by hand.

Ajouter un commentaire

Remove eleven 4mm Phillips #00 screws. Remove eleven 4mm Phillips #00 screws. Remove eleven 4mm Phillips #00 screws.
  • Remove eleven 4mm Phillips #00 screws.

Ajouter un commentaire

Apply a soldering iron to the solder joints to remove the two wires connecting the speaker to the circuit board.
  • Apply a soldering iron to the solder joints to remove the two wires connecting the speaker to the circuit board.

Ajouter un commentaire

If not already done, remove the circuit board completely from the case.
  • If not already done, remove the circuit board completely from the case.

Ajouter un commentaire

Desolder the two microphone solder joints.
  • Desolder the two microphone solder joints.

Ajouter un commentaire

The microphone should fall out after all the solder has been removed.
  • The microphone should fall out after all the solder has been removed.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Stuart

Membre depuis le 14/02/2018

425 Réputation

3 tutoriels rédigés

Équipe

USF Tampa, Team S3-G4, Nance Spring 2018 Membre de l'équipe USF Tampa, Team S3-G4, Nance Spring 2018

USFT-NANCE-S18S3G4

3 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 8

Total : 34