Introduction

The button pad lets the user control actions on the LCD screen. The arrow pad allows the user to move up, down, left, right, and select.

Pièces

Aucune pièce nécessaire.

Slide the door on the bottom of the camera in the direction of the open symbol with your finger. Release and the door will pop open. Release and the door will pop open.
  • Slide the door on the bottom of the camera in the direction of the open symbol with your finger.

  • Release and the door will pop open.

Ajouter un commentaire

Slide the battery out. Slide the battery out.
  • Slide the battery out.

Ajouter un commentaire

Remove lens cover from the camera by squeezing the protruding button on each side of the cover and pulling. Remove lens cover from the camera by squeezing the protruding button on each side of the cover and pulling.
  • Remove lens cover from the camera by squeezing the protruding button on each side of the cover and pulling.

Ajouter un commentaire

Pull the lens cover string toward the ground so that the loop underneath the metal slab is on top of the cover string. Push up so that the string starts to come out of the top of the loop. Grab the string from above the loop and pull.
  • Pull the lens cover string toward the ground so that the loop underneath the metal slab is on top of the cover string.

  • Push up so that the string starts to come out of the top of the loop.

  • Grab the string from above the loop and pull.

Ajouter un commentaire

Feed the string on top into the metal slab while pulling the loop toward you until the plastic piece stops you from pulling any further. Feed the string on top into the metal slab while pulling the loop toward you until the plastic piece stops you from pulling any further.
  • Feed the string on top into the metal slab while pulling the loop toward you until the plastic piece stops you from pulling any further.

Ajouter un commentaire

Separate the two pieces of the loop and pull the lens cover up in between them. Separate the two pieces of the loop and pull the lens cover up in between them. Separate the two pieces of the loop and pull the lens cover up in between them.
  • Separate the two pieces of the loop and pull the lens cover up in between them.

Ajouter un commentaire

Pull the lens cover and the sting will come out of the metal slab. Pull the lens cover and the sting will come out of the metal slab. Pull the lens cover and the sting will come out of the metal slab.
  • Pull the lens cover and the sting will come out of the metal slab.

Ajouter un commentaire

Flip open the door on the right side of the camera, when looking at the LCD screen. This door has a memory card and A/V OUT symbol on it. This door has a memory card and A/V OUT symbol on it.
  • Flip open the door on the right side of the camera, when looking at the LCD screen.

  • This door has a memory card and A/V OUT symbol on it.

Ajouter un commentaire

Gently push SD/MMC to eject. Gently push SD/MMC to eject.
  • Gently push SD/MMC to eject.

Ajouter un commentaire

Pull SD/MMC out of the camera. Pull SD/MMC out of the camera.
  • Pull SD/MMC out of the camera.

Ajouter un commentaire

Place lens cover back on the lens to prevent scratches or debris but leave string detached. Remove a total of six 3.968mm Phillips #00 screws. Two each from the left side, bottom, and right side. Remove a total of six 3.968mm Phillips #00 screws. Two each from the left side, bottom, and right side.
  • Place lens cover back on the lens to prevent scratches or debris but leave string detached.

  • Remove a total of six 3.968mm Phillips #00 screws. Two each from the left side, bottom, and right side.

Ajouter un commentaire

Pull the back cover away from the front cover. You may need to use a plastic opening tool as a wedge if it does not come apart by easily. You may need to use a plastic opening tool as a wedge if it does not come apart by easily.
  • Pull the back cover away from the front cover.

  • You may need to use a plastic opening tool as a wedge if it does not come apart by easily.

Ajouter un commentaire

Separate the back cover from the front cover.
  • Separate the back cover from the front cover.

Ajouter un commentaire

Remove two Phillips #00 screws from the inside of the button pad on the back cover. Remove two Phillips #00 screws from the inside of the button pad on the back cover. Remove two Phillips #00 screws from the inside of the button pad on the back cover.
  • Remove two Phillips #00 screws from the inside of the button pad on the back cover.

Ajouter un commentaire

Remove the metal piece shown. Remove the metal piece shown.
  • Remove the metal piece shown.

Ajouter un commentaire

Remove the black ring from the back and the white button pad will fall out from the front. Remove the black ring from the back and the white button pad will fall out from the front.
  • Remove the black ring from the back and the white button pad will fall out from the front.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Kirsten Price

Membre depuis le 17/09/2014

343 Réputation

6 tutoriels rédigés

Équipe

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 2

30 derniers jours : 5

Total : 291