Introduction

This guide will instruct how to install the power supply.

Turn the device so that the bottom is facing up.
  • Turn the device so that the bottom is facing up.

Ajouter un commentaire

Use the plastic opening tool to carefully lift the rubber stops in each corner. Do not completely remove the rubber stops, because they are difficult to replace. Do not completely remove the rubber stops, because they are difficult to replace.
  • Use the plastic opening tool to carefully lift the rubber stops in each corner.

  • Do not completely remove the rubber stops, because they are difficult to replace.

Ajouter un commentaire

Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device. Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.
  • Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.

Ajouter un commentaire

Lift the lower case straight up from the rest of the router. Lift the lower case straight up from the rest of the router.
  • Lift the lower case straight up from the rest of the router.

Ajouter un commentaire

Remove the clear plastic casing by lifting it straight up from the router. Remove the clear plastic casing by lifting it straight up from the router.
  • Remove the clear plastic casing by lifting it straight up from the router.

Ajouter un commentaire

Separate the motherboard from the top shell by lifting it straight up from the router. Separate the motherboard from the top shell by lifting it straight up from the router.
  • Separate the motherboard from the top shell by lifting it straight up from the router.

Ajouter un commentaire

Turn the motherboard, so that the top is facing upwards.
  • Turn the motherboard, so that the top is facing upwards.

  • Place the motherboard on a clean flat surface.

Ajouter un commentaire

Remove the yellow tape that holds the wire. Make sure that you set the tape aside on a clean surface, so that it can be reused.
  • Remove the yellow tape that holds the wire.

  • Make sure that you set the tape aside on a clean surface, so that it can be reused.

Ajouter un commentaire

Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard. The wire should now be completely separate from the motherboard. The wire should now be completely separate from the motherboard.
  • Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard.

  • The wire should now be completely separate from the motherboard.

Ajouter un commentaire

Extend the antenna away from the device, so that it becomes straight.
  • Extend the antenna away from the device, so that it becomes straight.

Ajouter un commentaire

Find the clips that hold the antenna onto the router. Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole. The antenna may take considerable force to remove.
  • Find the clips that hold the antenna onto the router.

  • Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole.

  • The antenna may take considerable force to remove.

Ajouter un commentaire

Completely separate the antenna and wire from the rest of the device.
  • Completely separate the antenna and wire from the rest of the device.

Ajouter un commentaire

Unscrew the two 5 mm  Phillips Head screws located at the front corners of the motherboard.
  • Unscrew the two 5 mm Phillips Head screws located at the front corners of the motherboard.

Ajouter un commentaire

Take off the metal frame. Take off the metal frame.
  • Take off the metal frame.

Ajouter un commentaire

Turn over the motherboard, so that the bottom is facing up.
  • Turn over the motherboard, so that the bottom is facing up.

Ajouter un commentaire

Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes. Desolder the three connections between the reset button and the motherboard
  • Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes.

  • Desolder the three connections between the reset button and the motherboard

  • For proper soldering and desoldering techniques, refer here.

  • Pull the power source from the other side of the mother board once the solder is liquid.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Nicole Slagle

Membre depuis le 25/01/2013

77 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 3-31, Amido Winter 2013 Membre de l'équipe Cal Poly, Team 3-31, Amido Winter 2013

CPSU-AMIDO-W13S3G31

3 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 6

Total : 1,395