Introduction

This guide will show you the necessary steps to replacing the chamber. The darts to be fired are loaded into the rotating chamber. Knowing how to remove the rotating chamber can help with problems such as a jammed gun or a dirty chamber. Common causes of a jammed gun are improperly placed darts or misaligned parts.

Pièces

Aucune pièce nécessaire.

Using a 00 Phillips screwdriver, remove all screws from the front panel. The screws have a length of .95 cm.
  • Using a 00 Phillips screwdriver, remove all screws from the front panel. The screws have a length of .95 cm.

Ajouter un commentaire

After the screws have been removed, gently lift the panel from the gun and set it aside.
  • After the screws have been removed, gently lift the panel from the gun and set it aside.

Ajouter un commentaire

Locate the black cylinder connected to the large spring near the top of the device.
  • Locate the black cylinder connected to the large spring near the top of the device.

  • Once located, push the black cylinder against the spring and lift it out of the device.

Ajouter un commentaire

Using your hand, lift the large spring and attached plastic stabilizing piece out of the gun and set aside. Ensure that the small spring connected to the stabilizing piece remains connected.
  • Using your hand, lift the large spring and attached plastic stabilizing piece out of the gun and set aside.

  • Ensure that the small spring connected to the stabilizing piece remains connected.

Ajouter un commentaire

Remove the two screws circled in blue. They are .95 cm in length.
  • Remove the two screws circled in blue. They are .95 cm in length.

  • Remove the three screw circled in green. They are .7 cm in length.

Ajouter un commentaire

Once all of the screws have been removed lift the pump handle off and set it aside.
  • Once all of the screws have been removed lift the pump handle off and set it aside.

Ajouter un commentaire

In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place. In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place.
  • In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place.

Ajouter un commentaire

Using a plastic opening tool, lift the white piece out of the gun and set it aside.
  • Using a plastic opening tool, lift the white piece out of the gun and set it aside.

Ajouter un commentaire

Using your hand, slide the track out of the gun by pulling it away form the device. Using your hand, slide the track out of the gun by pulling it away form the device.
  • Using your hand, slide the track out of the gun by pulling it away form the device.

Ajouter un commentaire

Using a plastic opening tool, detach the black piece from the trigger. You do not need to remove the black piece from the gun.
  • Using a plastic opening tool, detach the black piece from the trigger. You do not need to remove the black piece from the gun.

Ajouter un commentaire

Once the black piece has been detached, the trigger can be lifted out of the device.
  • Once the black piece has been detached, the trigger can be lifted out of the device.

Ajouter un commentaire

Once the trigger has been removed, simply pull the black connector out of the chamber. Set it aside.
  • Once the trigger has been removed, simply pull the black connector out of the chamber. Set it aside.

Ajouter un commentaire

With your hands gently grasp the barrel and chamber of the gun, and pull it away from the main body. With your hands gently grasp the barrel and chamber of the gun, and pull it away from the main body.
  • With your hands gently grasp the barrel and chamber of the gun, and pull it away from the main body.

Ajouter un commentaire

Using your hands, remove the barrel from the rotating chamber.
  • Using your hands, remove the barrel from the rotating chamber.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Bradley Penrow

Membre depuis le 23/09/2014

16 Réputation

4 tutoriels rédigés

Équipe

USF Tampa, Team 11-2, Blackwell Fall 2014 Membre de l'équipe USF Tampa, Team 11-2, Blackwell Fall 2014

USFT-BLACKWELL-F14S11G2

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 5

Total : 475