Introduction

In this guide you will learn how to remove and readjust the trigger of the device. Learning to do so will assist you with trouble shooting problems such as the sticking of the trigger when operating the device. This problem is usually caused by clogging of foreign objects within the device, spring malfunction, or misaligned pieces.

Pièces

Aucune pièce nécessaire.

Using a 00 Phillips screwdriver, remove all screws from the front panel. The screws have a length of .95 cm.
  • Using a 00 Phillips screwdriver, remove all screws from the front panel. The screws have a length of .95 cm.

Ajouter un commentaire

After the screws have been removed, gently lift the panel from the gun and set it aside.
  • After the screws have been removed, gently lift the panel from the gun and set it aside.

Ajouter un commentaire

Locate the black cylinder connected to the large spring near the top of the device.
  • Locate the black cylinder connected to the large spring near the top of the device.

  • Once located, push the black cylinder against the spring and lift it out of the device.

Ajouter un commentaire

Using your hand, lift the large spring and attached plastic stabilizing piece out of the gun and set aside. Ensure that the small spring connected to the stabilizing piece remains connected.
  • Using your hand, lift the large spring and attached plastic stabilizing piece out of the gun and set aside.

  • Ensure that the small spring connected to the stabilizing piece remains connected.

Ajouter un commentaire

Remove the two screws circled in blue. They are .95 cm in length.
  • Remove the two screws circled in blue. They are .95 cm in length.

  • Remove the three screw circled in green. They are .7 cm in length.

Ajouter un commentaire

Once all of the screws have been removed lift the pump handle off and set it aside.
  • Once all of the screws have been removed lift the pump handle off and set it aside.

Ajouter un commentaire

In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place. In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place.
  • In order to remove the white plastic holder, you must remove the spring that keeps it in place. Using a 00 Phillips screwdriver, carefully remove the screw while holding the spring in place.

Ajouter un commentaire

Using a plastic opening tool, lift the white piece out of the gun and set it aside.
  • Using a plastic opening tool, lift the white piece out of the gun and set it aside.

Ajouter un commentaire

Using your hand, slide the track out of the gun by pulling it away form the device. Using your hand, slide the track out of the gun by pulling it away form the device.
  • Using your hand, slide the track out of the gun by pulling it away form the device.

Ajouter un commentaire

Using a plastic opening tool, detach the black piece from the trigger. You do not need to remove the black piece from the gun.
  • Using a plastic opening tool, detach the black piece from the trigger. You do not need to remove the black piece from the gun.

Ajouter un commentaire

Once the black piece has been detached, the trigger can be lifted out of the device.
  • Once the black piece has been detached, the trigger can be lifted out of the device.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order. Ensure that the spring located behind the trigger is attached to the limb on the backside of the trigger.

Bradley Penrow

Membre depuis le 23/09/2014

16 Réputation

4 tutoriels rédigés

Équipe

USF Tampa, Team 11-2, Blackwell Fall 2014 Membre de l'équipe USF Tampa, Team 11-2, Blackwell Fall 2014

USFT-BLACKWELL-F14S11G2

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 2

Total : 297