Introduction

This is a step-by-step guide on how to remove the lens assembly PCB board in a Netgear Arlo. Remove the batteries before beginning this guide.

Remove the 2 (3.5mm) housing screws with a J0 screwdriver.
  • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

Ajouter un commentaire

Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover. Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.
  • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Ajouter un commentaire

Open the battery cover and remove the  2 (3.5mm") screws from under the cover.
  • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Ajouter un commentaire

Idées cadeaux pour la Fête des Pères
Mettons nos papas à l’honneur ainsi que nos mentors qui nous ont appris à réparer.
Idées cadeaux pour la Fête des Pères
Honorons ceux qui nous ont enseigné à réparer.
Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover. Next,  start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line. Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.
  • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

  • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

  • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Ajouter un commentaire

Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on. Remove the second screw (3.5mm) on the back of the camera to remove the second housing. Once the screws are removed use an opening tool to pry back the second plastic mount.
  • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

  • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

  • Once the screws are removed use an opening tool to pry back the second plastic mount.

Ajouter un commentaire

Remove 4 (6mm) large screws with a J00 screwdriver.
  • Remove 4 (6mm) large screws with a J00 screwdriver.

  • There are 2 on each side. This will allow you to remove the clear housing from the white housing.

Ajouter un commentaire

Once screws are removed, pull apart the clear housing. Remove rod from camera cover.
  • Once screws are removed, pull apart the clear housing.

  • Remove rod from camera cover.

Ajouter un commentaire

Remove Large ribbon cable first to disconnect front of camera from main body. Remove 4 (3.5mm) small black screws from motherboard of the camera unit. Remove smaller ribbon cable from underneath yellow tape.
  • Remove Large ribbon cable first to disconnect front of camera from main body.

  • Remove 4 (3.5mm) small black screws from motherboard of the camera unit.

  • Remove smaller ribbon cable from underneath yellow tape.

Ajouter un commentaire

Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.
  • Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Connor Krampen

Membre depuis le 08/01/2018

375 Réputation

3 tutoriels rédigés

Équipe

IUPUI, Team S1-G1, Freund Spring 2018 Membre de l'équipe IUPUI, Team S1-G1, Freund Spring 2018

IUPUI-FREUND-S18S1G1

2 membres

3 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 20

30 derniers jours : 88

Total : 216