Introduction

Replacing the logic board of a Nikon Coolpix 3500

Pièces

Aucune pièce nécessaire.

Unlatch the battery cover. Slide the cover out and flip it open.
  • Unlatch the battery cover. Slide the cover out and flip it open.

  • Remove the battery.

  • Gently remove the battery cover.

Ajouter un commentaire

Remove the two 4.5 mm screws that sit next to the battery slot.
  • Remove the two 4.5 mm screws that sit next to the battery slot.

  • Remove the 3 mm screw that sits below the CF card slot.

  • Remove the 4.5 mm screw that sits above the digital I/O cover.

Ajouter un commentaire

Remove the two 4.5 mm screws that sit inside the battery slot.
  • Remove the two 4.5 mm screws that sit inside the battery slot.

Ajouter un commentaire

Remove the two 5 mm screws that sit near the camera strap eyelet.
  • Remove the two 5 mm screws that sit near the camera strap eyelet.

  • Remove the camera strap eyelet.

Ajouter un commentaire

Remove the 5 mm screw and cap that were underneath the camera strap eyelet.
  • Remove the 5 mm screw and cap that were underneath the camera strap eyelet.

Ajouter un commentaire

Remove the five 3.5 mm screws that sit at the bottom of the camera. Remove the grey plastic piece, which the five screws held in place, by gently detaching the front cover.
  • Remove the five 3.5 mm screws that sit at the bottom of the camera.

  • Remove the grey plastic piece, which the five screws held in place, by gently detaching the front cover.

  • Do not apply too much force; two wires still connect the front cover to the logic board.

Ajouter un commentaire

Using a spudger, detach the white-capped wire. Using a spudger, detach the orange-capped wire and set the front cover aside.
  • Using a spudger, detach the white-capped wire.

  • Using a spudger, detach the orange-capped wire and set the front cover aside.

Ajouter un commentaire

Detach the grey-capped wire.
  • Detach the grey-capped wire.

  • Detach the green chip that sits next to the blue wires.

Ajouter un commentaire

Remove the 3.5 mm screw that sits next to the rotating lens. Invert the logic board and lens to uncover the orange and blue ribbon cables. These cables still connect the logic board to the LCD screen.
  • Remove the 3.5 mm screw that sits next to the rotating lens.

  • Invert the logic board and lens to uncover the orange and blue ribbon cables. These cables still connect the logic board to the LCD screen.

Ajouter un commentaire

Detach the blue ribbon cable. Detach the orange ribbon cable by using a spudger, and while pushing it out horizontally.
  • Detach the blue ribbon cable.

  • Detach the orange ribbon cable by using a spudger, and while pushing it out horizontally.

  • Detach the red-capped wire.

  • Lift the logic board and lens, which are still connected, out of the back cover.

Ajouter un commentaire

Lift the black covering and remove the orange ribbon cable, which connects the lens to the logic board.
  • Lift the black covering and remove the orange ribbon cable, which connects the lens to the logic board.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

richard guenther

Membre depuis le 19/04/2010

183 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 30-38, Garner Spring 2010 Membre de l'équipe Cal Poly, Team 30-38, Garner Spring 2010

CPSU-GARNER-S10S30G38

5 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 1,870