Pièces

Aucune pièce nécessaire.

Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.
  • Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.

Ajouter un commentaire

Remove the 3 screws under the battery flap and remove the bottom cover.
  • Remove the 3 screws under the battery flap and remove the bottom cover.

Ajouter un commentaire

Remove the 2 screws inside the camera on the back corners.
  • Remove the 2 screws inside the camera on the back corners.

Ajouter un commentaire

Open the HDMI flap and remove the 2 screws.
  • Open the HDMI flap and remove the 2 screws.

Ajouter un commentaire

Remove the screw next to the camera strap loop.
  • Remove the screw next to the camera strap loop.

Ajouter un commentaire

Remove the 2 screws on each side of the view finder.
  • Remove the 2 screws on each side of the view finder.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Remove the 2 screws above and below the SD card flap.
  • Remove the 2 screws above and below the SD card flap.

Ajouter un commentaire

Peel off the adhesive leather screw cover and  remove the 2 screws under it.
  • Peel off the adhesive leather screw cover and remove the 2 screws under it.

Ajouter un commentaire

Remove the Diopter adjustment control sticker and remove the screw under it. Remove the Diopter adjustment control sticker and remove the screw under it.
  • Remove the Diopter adjustment control sticker and remove the screw under it.

Ajouter un commentaire

Separate the back panel of the camera from the actual camera.
  • Separate the back panel of the camera from the actual camera.

  • Be careful not to tear any of the ribbon cables.

Ajouter un commentaire

Disconnect the LCD ribbon cables and power cable from the motherboard.
  • Disconnect the LCD ribbon cables and power cable from the motherboard.

Ajouter un commentaire

Unscrew all 16 screws around the back plate of the camera. Unscrew all 16 screws around the back plate of the camera.
  • Unscrew all 16 screws around the back plate of the camera.

Ajouter un commentaire

Then unscrew the remaining screws holding the back plate to the LCD.
  • Then unscrew the remaining screws holding the back plate to the LCD.

  • Then simply remove the plate with the LCD.

Ajouter un commentaire

Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.
  • Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.

Ajouter un commentaire

Remove the black 4 pin connector by pulling it out of the connector.
  • Remove the black 4 pin connector by pulling it out of the connector.

Ajouter un commentaire

Remove the 7 screws holding the motherboard in place.
  • Remove the 7 screws holding the motherboard in place.

Ajouter un commentaire

This is what you should see after removing the motherboard.
  • This is what you should see after removing the motherboard.

Ajouter un commentaire

After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.
  • After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Wesley Eveld

Membre depuis le 20/02/2018

541 Réputation

4 tutoriels rédigés

Équipe

USF Tampa, Team S11-G6, Cheng Spring 2018 Membre de l'équipe USF Tampa, Team S11-G6, Cheng Spring 2018

USFT-CHENG-S18S11G6

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 15

Total : 38