Introduction

Get the power flowing through your DSi XL by replacing the power board.

Remove the two Phillips screws securing the battery cover to the back of the handheld console. Lift the battery cover off the back of the DSi XL.
  • Remove the two Phillips screws securing the battery cover to the back of the handheld console.

  • Lift the battery cover off the back of the DSi XL.

Ajouter un commentaire

Lift the battery from the DSi XL.
  • Lift the battery from the DSi XL.

Ajouter un commentaire

Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin.
  • Remove the four rubber screw covers on the lower case by prying them up with a push pin.

Ajouter un commentaire

Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
  • Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:

    • Four silver 5.3 mm screws

    • Two black 5.3 mm screws

    • One black 2.5 mm screw

Ajouter un commentaire

Turn the DSi XL over, and open the display. Insert a spudger between the upper and lower case at the bottom left corner of the DSi. Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.
  • Turn the DSi XL over, and open the display.

  • Insert a spudger between the upper and lower case at the bottom left corner of the DSi.

  • Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.

Ajouter un commentaire

Close the display and turn the DSi XL over. Lift the lower case from the front edge.
  • Close the display and turn the DSi XL over.

  • Lift the lower case from the front edge.

  • Rotate the lower case away from the DSi.

  • The lower case cannot be completely removed yet, since it is still connected to the motherboard.

Ajouter un commentaire

Using a spudger, pry the SD card/right shoulder button connector off its socket. Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
  • Using a spudger, pry the SD card/right shoulder button connector off its socket.

  • Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.

Ajouter un commentaire

Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable. With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.
  • Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable.

  • With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.

Ajouter un commentaire

Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.
  • Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.

    • Use caution, as the wires are very fragile and could come out of the connector if pulled on too hard.

Ajouter un commentaire

Remove the seven 2.5 mm silver screws securing the power board to the upper case. Lift the power board off the upper case.
  • Remove the seven 2.5 mm silver screws securing the power board to the upper case.

  • Lift the power board off the upper case.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Brett Hartt

Membre depuis le 12/04/2010

105 064 Réputation

315 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

116 membres

5 774 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 12

30 derniers jours : 34

Total : 13,394