Introduction

You need a T5 screwdriver to remove the screws.

Pièces

Aucune pièce nécessaire.

In order to remove the back cover, you must press the indicated button.
  • In order to remove the back cover, you must press the indicated button.

Ajouter un commentaire

With the button pressed, apply light pressure and slide the back cover off. This will allow you to access the battery
  • With the button pressed, apply light pressure and slide the back cover off.

  • This will allow you to access the battery

Ajouter un commentaire

In order to remove the battery, pull it out from the same side that the rubber button is on.
  • In order to remove the battery, pull it out from the same side that the rubber button is on.

Ajouter un commentaire

Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone.
  • Using a plastic opening tool, separate the back cover from the phone.

Ajouter un commentaire

Continue along the edge with the plastic opening tool. Continue along the edge with the plastic opening tool.
  • Continue along the edge with the plastic opening tool.

Ajouter un commentaire

Gently, remove the back cover. Gently, remove the back cover. Gently, remove the back cover.
  • Gently, remove the back cover.

Ajouter un commentaire

Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver.
  • Unscrew the indicated screws using the T5 screwdriver.

Ajouter un commentaire

Open the phone up and use the plastic opening tool to remove the cover to the keyboard. Be careful not to break the plastic during this step; do your best not to force anything.
  • Open the phone up and use the plastic opening tool to remove the cover to the keyboard.

  • Be careful not to break the plastic during this step; do your best not to force anything.

Ajouter un commentaire

The button board will be loose once the cover is removed. Lift it up to reveal the sensor board.
  • The button board will be loose once the cover is removed.

  • Lift it up to reveal the sensor board.

Ajouter un commentaire

With the T5 Screwdriver, remove the marked screws. With the T5 Screwdriver, remove the marked screws.
  • With the T5 Screwdriver, remove the marked screws.

Ajouter un commentaire

With the screws removed, the sensor board should be free to flip up. With the screws removed, the sensor board should be free to flip up.
  • With the screws removed, the sensor board should be free to flip up.

Ajouter un commentaire

Disconnect the wire with the plastic opening tool. Disconnect the wire with the plastic opening tool.
  • Disconnect the wire with the plastic opening tool.

Ajouter un commentaire

Remove the screws marked. The Screw on the left is located underneath the cable. With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.
  • Remove the screws marked.

  • The Screw on the left is located underneath the cable.

  • With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autre(s) ont terminé cette réparation.

Cameron Weinberg

Membre depuis le 12/04/2011

444 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 18-21, Garner Spring 2011 Membre de l'équipe Cal Poly, Team 18-21, Garner Spring 2011

CPSU-GARNER-S11S18G21

4 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 8

30 derniers jours : 25

Total : 5,332