Réparez vos affaires Communauté Boutique

Philips DVP642 Power Supply Replacement

Introduction

This guide will walk you through removing the old power supply for the DVD player so that a new one may be installed. This guide will also show you how to replace a blown fuse if needed.

Ce dont vous avez besoin

  1. Philips DVP642 Power Supply Replacement, Top Panel: étape 1, image 1 de 2 Philips DVP642 Power Supply Replacement, Top Panel: étape 1, image 2 de 2

    • Remove four 7.5 mm Phillips screws on the both sides (2 on each side).

    • Remove five 7.5 mm Phillips screws on the back of the player.

    Traduire

  2. Philips DVP642 Power Supply Replacement: étape 2, image 1 de 2 Philips DVP642 Power Supply Replacement: étape 2, image 2 de 2

    • Lift the top panel from the back and remove. It should come off without being forced. There is a lip near the front so you many need to slide the top panel back slightly to remove it.

    Traduire

  3. Philips DVP642 Power Supply Replacement, Power Supply: étape 3, image 1 de 2 Philips DVP642 Power Supply Replacement, Power Supply: étape 3, image 2 de 2

    • Slide the power cord out from the case.

    • Be sure not to lose the rubber clip that is wrapped around the cord.

    Traduire

  5. Philips DVP642 Power Supply Replacement: étape 4, image 1 de 1

    • Remove the ribbon attached to the power supply by pushing the latch and gently pulling up.

    Traduire

  6. Philips DVP642 Power Supply Replacement: étape 5, image 1 de 2 Philips DVP642 Power Supply Replacement: étape 5, image 2 de 2

    • Now remove this ribbon wire by grasping the white head firmly and pulling up gently.

    Traduire

  7. Philips DVP642 Power Supply Replacement: étape 6, image 1 de 2 Philips DVP642 Power Supply Replacement: étape 6, image 2 de 2

    • Remove these two 7.5m Phillips screws and the matching set at the other end of the supply.

    • Now remove the ribbon that attaches the power supply to the motherboard by grasping the white head and gently pulling up.

    Traduire

  8. Philips DVP642 Power Supply Replacement: étape 7, image 1 de 3 Philips DVP642 Power Supply Replacement: étape 7, image 2 de 3 Philips DVP642 Power Supply Replacement: étape 7, image 3 de 3

    • Remove the last screw.

    • Pinch this plastic prong and slide the power supply up and over it. The power supply should lift free.

    Traduire

  9. Philips DVP642 Power Supply Replacement: étape 8, image 1 de 2 Philips DVP642 Power Supply Replacement: étape 8, image 2 de 2

    • Your power supply is now free!

    • If the fuse circled here is blown (the small wire in the glass tube is missing or broken), remove it by pinching it tightly and pulling it straight out.

    • You can find a new fuse here.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

7 autres ont terminé cette réparation.

Auteur

avec 4 autres contributeurs

Toby Goldsteinholm

Membre depuis le 10/09/11

360 Réputation

2 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 21-20, Maness Fall 2011 Membre de l'équipe Cal Poly, Team 21-20, Maness Fall 2011

CPSU-MANESS-F11S21G20

4 membres

7 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 6

30 derniers jours : 43

Total : 13,330