Introduction

How to disassemble and change the Laser Unit.

Vidéo d'introduction

Turn off the console and disconnect all cables.
  • Turn off the console and disconnect all cables.

Ajouter un commentaire

You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.
  • You must remove the warranty sticker and 4 screws.

Ajouter un commentaire

After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.
  • After removing HDD bay cover, you will see another 3 screw.

Ajouter un commentaire

Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.
  • Push there to release and remove upper back bezel.

Ajouter un commentaire

The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.
  • The upper front bezel is harder to remove.

Ajouter un commentaire

Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.
  • Remove 7 screws to release top cover.

Ajouter un commentaire

Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.
  • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

Ajouter un commentaire

To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.
  • To release the laser unit disconnect this flex-cable.

Ajouter un commentaire

One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.
  • One flex-cable, for rubbers and the metal bezel.

Ajouter un commentaire

Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.
  • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

Ajouter un commentaire

Assembling, assembling... Assembling, assembling... Assembling, assembling...
  • Assembling, assembling...

Ajouter un commentaire

Let's test the device before fully assembling it. .

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

9 autre(s) ont terminé cette réparation.

ZFix

Membre depuis le 09/12/2013

153 600 Réputation

430 tutoriels rédigés

Équipe

Master Techs Membre de l'équipe Master Techs

Community

277 membres

724 tutoriels rédigés

Very good job, kudos!

Kevin Borras - Réponse

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 55

30 derniers jours : 175

Total : 17,159