Introduction

This guide will tell you exactly what to do if you have a problem with the buttons on your camera.

Using a #00 screw driver, remove the four screws on the left side of the camera. Using a #00 screw driver, remove the three screws on the right side of the camera. Using a #00 screw driver, remove the two screws on the bottom of the camera.
  • Using a #00 screw driver, remove the four screws on the left side of the camera.

  • Using a #00 screw driver, remove the three screws on the right side of the camera.

  • Using a #00 screw driver, remove the two screws on the bottom of the camera.

Ajouter un commentaire

Slide open the battery door and use a plastic opening tool to slightly open the side of the case. Gently pull apart the cover with the LCD screen attached from the rest of the camera.
  • Slide open the battery door and use a plastic opening tool to slightly open the side of the case.

  • Gently pull apart the cover with the LCD screen attached from the rest of the camera.

  • Do not pull the cover off completely because it is still attached to the logic board.

Ajouter un commentaire

Locate where the LCD screen ribbon is attached to the logic board. Using the plastic opening tool, flip the black tab away from you that connects the LCD screen ribbon to the logic board. Gently pull the ribbon away from the logic board.
  • Locate where the LCD screen ribbon is attached to the logic board.

  • Using the plastic opening tool, flip the black tab away from you that connects the LCD screen ribbon to the logic board.

  • Gently pull the ribbon away from the logic board.

Ajouter un commentaire

Now you have separated the back half of the camera from the rest of it.
  • Now you have separated the back half of the camera from the rest of it.

  • If you have problems with your menu buttons, you must replace the entire back half of the outer case. Not including the screen.

  • If you do not have problems with your menu buttons ONLY your snap button (the one that you push to take pictures) skip ahead to step 7

Ajouter un commentaire

Now that the cover with the screen attached is removed from the rest of the camera, locate the four screws at each corner of the LCD screen. Remove these four screws.
  • Now that the cover with the screen attached is removed from the rest of the camera, locate the four screws at each corner of the LCD screen. Remove these four screws.

Ajouter un commentaire

Remove the LCD screen from the casing of the camera
  • Remove the LCD screen from the casing of the camera

  • Now you may replace the back case with a case with working buttons.

Ajouter un commentaire

Using a #00 screw driver remove the screw on the bottom of the logic board, just above the tripod attachment. Gently pull the front of the case away from the insides of the camera
  • Using a #00 screw driver remove the screw on the bottom of the logic board, just above the tripod attachment.

  • Gently pull the front of the case away from the insides of the camera

Ajouter un commentaire

Locate the button that will be removed. Gently push it out. Push from the inside of the camera towards the outside.
  • Locate the button that will be removed.

  • Gently push it out. Push from the inside of the camera towards the outside.

Ajouter un commentaire

Now you may replace your button.
  • Now you may replace your button.

  • There will be a spring underneath the button. Be sure not to lose it and to put it back in when replacing the button.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Terichael Office

Membre depuis le 24/06/2010

9 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 3-4, Johann Summer 2010 Membre de l'équipe Cal Poly, Team 3-4, Johann Summer 2010

CPSU-JOHANN-R10S3G4

4 membres

4 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 2,178