Pièces

Aucune pièce nécessaire.

Unscrew and remove the four screws from the left side of the camera (from the screen's view) Unscrew and remove the four screws from the left side of the camera (from the screen's view)
  • Unscrew and remove the four screws from the left side of the camera (from the screen's view)

Ajouter un commentaire

Unscrew and remove the three screws from the bottom of the camera
  • Unscrew and remove the three screws from the bottom of the camera

Ajouter un commentaire

Unscrew and remove the two screws from the right side of the camera. Unscrew and remove the two screws from the right side of the camera.
  • Unscrew and remove the two screws from the right side of the camera.

Ajouter un commentaire

Open the battery flap and remove the batteries. Keep the battery flap open.
  • Open the battery flap and remove the batteries.

  • Keep the battery flap open.

Ajouter un commentaire

Use a spudger to gently separate the two halves of the camera's outer casing.
  • Use a spudger to gently separate the two halves of the camera's outer casing.

Ajouter un commentaire

Gently pull the half of the case with the screen (the back half) from the rest of the camera.
  • Gently pull the half of the case with the screen (the back half) from the rest of the camera.

  • Be sure not too pull to hard. The screen is still attached to the motherboard. If you pull too hard you will rip it.

Ajouter un commentaire

The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon. The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon.
  • The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon.

Ajouter un commentaire

Use a spudger to lift the black flap that clamps the ribbon towards you. When the black flap is open it will be straight up. (like in the second picture)
  • Use a spudger to lift the black flap that clamps the ribbon towards you.

  • When the black flap is open it will be straight up. (like in the second picture)

Ajouter un commentaire

Now that the black flap is open, gently pull the ribbon out.
  • Now that the black flap is open, gently pull the ribbon out.

  • You should now have the back half of the camera completely separate from the rest of the camera.

Ajouter un commentaire

This is what the back half of the camera should look like. This is what the rest of the camera will look like.
  • This is what the back half of the camera should look like.

  • This is what the rest of the camera will look like.

Ajouter un commentaire

Unscrew and remove two screws from the logic board.
  • Unscrew and remove two screws from the logic board.

Ajouter un commentaire

Pull the front half off of the logic board.
  • Pull the front half off of the logic board.

Ajouter un commentaire

This will be the front half of the outer case.
  • This will be the front half of the outer case.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Terichael Office

Membre depuis le 24/06/2010

9 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 3-4, Johann Summer 2010 Membre de l'équipe Cal Poly, Team 3-4, Johann Summer 2010

CPSU-JOHANN-R10S3G4

4 membres

4 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 1,230