Introduction

Removing the power supply of the Power Mac G4.

The handle to open your computer is located on top of the right side panel.
  • The handle to open your computer is located on top of the right side panel.

Ajouter un commentaire

Grab the circular handle and pull outward. Grab the circular handle and pull outward.
  • Grab the circular handle and pull outward.

Ajouter un commentaire

Your computer is now open and ready for repair.
  • Your computer is now open and ready for repair.

Ajouter un commentaire

The optical drive is in the top left corner of the case.
  • The optical drive is in the top left corner of the case.

Ajouter un commentaire

There are four screws to be removed. The first screw can be seen in the first picture.
  • There are four screws to be removed.

  • The first screw can be seen in the first picture.

  • The remaining three screws can be seen in the second picture.

Ajouter un commentaire

Remove the optical drive by pulling the drive away from the front of the computer and out.
  • Remove the optical drive by pulling the drive away from the front of the computer and out.

Ajouter un commentaire

Detach the two cables attached to the back of the drive.
  • Detach the two cables attached to the back of the drive.

  • The flat ribbon cable can be detached by pulling the silver tab. The multicolored cable can be removed by grasping the plastic connector on either side and pulling with substantial force.

Ajouter un commentaire

The hard drive is located in the back right corner of the case.
  • The hard drive is located in the back right corner of the case.

Ajouter un commentaire

Remove the flat ribbon cable by pulling with substantial force.
  • Remove the flat ribbon cable by pulling with substantial force.

Ajouter un commentaire

Remove the screw holding the hard drive to the computer.
  • Remove the screw holding the hard drive to the computer.

Ajouter un commentaire

Pull the drive up and out of the computer.
  • Pull the drive up and out of the computer.

Ajouter un commentaire

Remove the multicolored cable by grasping the plastic connector on either side and pulling with substantial force.
  • Remove the multicolored cable by grasping the plastic connector on either side and pulling with substantial force.

Ajouter un commentaire

The power supply is in the upper right corner of the case.
  • The power supply is in the upper right corner of the case.

Ajouter un commentaire

There is a total of four screws to be removed. The first three can be seen in the first picture.
  • There is a total of four screws to be removed.

  • The first three can be seen in the first picture.

  • The final screw can be seen in the second picture.

Ajouter un commentaire

There are three 2.5mm hex bolts located in the back of the computer that also need to be removed.
  • There are three 2.5mm hex bolts located in the back of the computer that also need to be removed.

  • A 3/32" Hex Key or Hex Driver is a bit small but may also work if gentle.

Ajouter un commentaire

Disconnect the power supply cables from the mother board by pressing in the tab on the back of the connector as shown.
  • Disconnect the power supply cables from the mother board by pressing in the tab on the back of the connector as shown.

This step can be done prior to Step 13.

dec59us - Réponse

Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!
  • Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!

  • Slide the power supply away from the back of the computer and pull it out carefully stringing the cables through the hole in the metal support.

Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!

7design - Réponse

Your power supply is now free from the enclosure and is ready to be replaced.
  • Your power supply is now free from the enclosure and is ready to be replaced.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

18 autre(s) ont terminé cette réparation.

Jacob Garcia

Membre depuis le 28/01/2010

483 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 14-41, Regan Winter 2010 Membre de l'équipe Cal Poly, Team 14-41, Regan Winter 2010

CPSU-REGAN-W10S14G41

4 membres

10 tutoriels rédigés

I hate to say this, but that is not fixing the power supply but replacing the power supply with a new unit. i was hoping to fix it as mine blew and was hoping to revive it, but not luck on this end by the look of it. :(

Yannick Docq - Réponse

Thanks for the clear instructions to replace the power supply. I got my part on eBay for $29 (other online stores are charging $100-200+ for it) to doctor up an old G4, and it works like a charm now.

Brenna Jue - Réponse

Thank you so very much for these instructions. On my 733 G4 the blue front panel had to be removed to allow the DVD drive to exit from the front of the machine. I also had to remove the fan to allow the wires to exit with the power supply.

John - Réponse

Yet another G4 QuickSilver saved from the electronics recycler! In tandem with an eBay-listed refurbisher of my defunct PSU, it was brought back to life. Instructions were very clear.

dec59us - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 16

30 derniers jours : 76

Total : 25,175