Il est possible que cette traduction ne reflète pas les dernières mises à jour du tutoriel source. Aidez à mettre à jour la traduction ou bien consultez le tutoriel source.
Introduction
Consultez ce tutoriel pour remplacer l'adhésif et sceller à nouveau votre Apple Watch Series 2. Il se peut que l'étanchéité à l'eau de la Apple Watch ne soit pas complètement restituée après cette procédure.
Ce dont vous avez besoin
-
-
Imbibez un coton-tige d'un peu d'alcool isopropylique (>99%) ou servez-vous d'une lingette nettoyante pour enlever délicatement les résidus d'adhésif sur le joint Force Touch.
-
-
-
Retournez l'Apple Watch de sorte que les nappes de l'écran sont à plat et le fond à la verticale.
-
Enlevez les résidus au dos de l'écran.
-
-
-
-
Prenez une pincette pour décoller délicatement la bande de remplacement avec son film de protection bleu du papier support.
-
-
-
Tenez la bande adhésive de travers pour la faire passer par-dessus l'écran.
-
Faites délicatement pivoter l'écran vers l'avant de façon à aligner la bande avec le châssis.
-
Positionnez celle-ci sur le joint Force Touch et appuyez dessus avec la pointe d'une spatule pour la faire adhérer.
-
Annulation : je n'ai pas terminé ce tutoriel.
20 autres ont terminé cette réparation.
Merci à ces traducteurs :
91%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
7 commentaires
Will the new adhesive be water proof?
or will the watch after replacement no longer be water proof?
The Apple Watch isn’t waterproof, but water resistant. After opening and resealing it there is no guaranty that the resistance is the same as before. More on that topic can also be read on Apples website (“Apple Watch can't be rechecked or resealed for water resistance.“). But when resealed properly (using heat and pressure without damaging the force touch gasket in the opening process and cleaning off old residue) there shouldn’t be any concern for a normal daily use like washing hands or taking a shower. It might even work for a swim in a pool or an ocean, but I wouldn’t count on that 50M ISO rating ;)
This one was a bugger! Dang…getting this over the display w/o sticking to everything is an exercise puzzle. The first one also didn't release correctly and I ended up installing just the blue adhesive backing…then realized that the adhesive was still on the other backing, which I then had to very carefully remove with a tweezers, then navigate the puzzle of an exercise getting it over the display and in to position. I did it, but as other commenters noted, it is not sealed anything like it originally was. In fact, it came up in a few days and I had to use the iRemover to heat it back up and press it back into place. I also use an iWatch bumper guard all the time now to protect it from popping off. For this older series 2 iWatch I’m ok.
Thank you iFixIt for top notch parts, instructions and tutorials. I’ve been an IT tech/specialist for many years, but still approach new repairs with caution, especially on Apple products, until I’ve done it at least once.
Yes, resealing the Apple Watch is a tough one. It is either disconnecting the display and go without the "exercise puzzle" but risk damaging cables and having to reconnect the display vs. keeping a steady hand and feeding the adhesive around the display.
I edited the guide to apply pressure on the closed watch for a longer time now. A few hours under some heavy books might do a better job.
Oh, and congrats on the repair.
Adhesive gasket/strip did not fit. It was slightly undersized :( I ended up cutting tiny strips to fill the gaps. :(
