Introduction

This guide will show how to replace the speaker on the Casio camera

Pièces

Aucune pièce nécessaire.

Remove the four screws on the side with the speaker
  • Remove the four screws on the side with the speaker

Ajouter un commentaire

Remove the four screws from the bottom of the camera.
  • Remove the four screws from the bottom of the camera.

  • Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly

Ajouter un commentaire

Remove the four screws on the side opposite of the speaker.
  • Remove the four screws on the side opposite of the speaker.

Ajouter un commentaire

Pull apart the bottom casing.
  • Pull apart the bottom casing.

Ajouter un commentaire

Remove ribbon from the rear casing. Set aside rear casing.
  • Remove ribbon from the rear casing.

  • Set aside rear casing.

Ajouter un commentaire

Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.
  • Use tweezers or prongs to pry the LCD screen off from the opening.

  • Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

Ajouter un commentaire

Lift up the LCD screen, slowly move it to the other side. Lift up the LCD screen, slowly move it to the other side.
  • Lift up the LCD screen, slowly move it to the other side.

Ajouter un commentaire

Pry off the LCD casing which is taped on to the frame. Pry off the LCD casing which is taped on to the frame.
  • Pry off the LCD casing which is taped on to the frame.

Ajouter un commentaire

Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera. Pull out the LCD screen with the ribbon from the camera.
  • Flip open the connector holding the ribbon.

  • Pull out the LCD screen with the ribbon from the camera.

Ajouter un commentaire

Pull apart the front casing. Pull apart the front casing.
  • Pull apart the front casing.

Ajouter un commentaire

Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
  • Remove two screws on the side where the battery is located.

  • Remove the lanyard loop after the screws come off.

  • Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

Ajouter un commentaire

On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.
  • On the front of the camera near the flash flip the connector holding the ribbon.

  • Remove the ribbon from the connector.

Ajouter un commentaire

Carefully remove the L shaped frame from the camera At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs.
  • Carefully remove the L shaped frame from the camera

  • At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab.

  • Pop the frame off the bumps and tabs.

  • Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off.

  • The blue box is the speaker

Ajouter un commentaire

Remove the speaker with tweezers
  • Remove the speaker with tweezers

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Christian

Membre depuis le 28/01/2011

320 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team 4-38, Regan Winter 2011 Membre de l'équipe Cal Poly, Team 4-38, Regan Winter 2011

CPSU-REGAN-W11S4G38

4 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 2,510