Danger
Potentiellement dangereux
Risque de blessure si cette procédure n'est pas suivie correctement. Faites preuve de prudence et suivez tous les avertissements.
Danger

Introduction

The Quasar MQ7774XW microwave was introduced in 1984. This replacement repair guide shows the necessary steps that must be taken if sparking occurs on the inside of the microwave.

Pièces

Disconnect the power supply cord from the outlet.
  • Disconnect the power supply cord from the outlet.

Ajouter un commentaire

Remove the eight screws holding the wood-patterned cover to the microwave frame. The first four screws are located on either side of the microwave front.
  • Remove the eight screws holding the wood-patterned cover to the microwave frame.

  • The first four screws are located on either side of the microwave front.

Ajouter un commentaire

Remove the additional four screws securing the wood-paneled case to the microwave frame. Remove the additional four screws securing the wood-paneled case to the microwave frame.
  • Remove the additional four screws securing the wood-paneled case to the microwave frame.

Ajouter un commentaire

Placing your hands on either side of the case, slide the case back gently until you feel it completely separate from the microwave frame. Lift the case upward slowly until the case is free of the microwave. Lift the case upward slowly until the case is free of the microwave.
  • Placing your hands on either side of the case, slide the case back gently until you feel it completely separate from the microwave frame.

  • Lift the case upward slowly until the case is free of the microwave.

Ajouter un commentaire

First check to see if the interior of the microwave is dirty. Food or tin foil could be the reason that the microwave is sparking.
  • First check to see if the interior of the microwave is dirty. Food or tin foil could be the reason that the microwave is sparking.

  • If the interior of the microwave is dirty, clean it. A spotless interior is recommended. The interior should look like the example in the picture.

Ajouter un commentaire

If the microwave continues to spark after the interior has been cleaned, that could indicate that the diode may be broken. The diode is what attaches the capacitor to the back of the microwave.
  • If the microwave continues to spark after the interior has been cleaned, that could indicate that the diode may be broken. The diode is what attaches the capacitor to the back of the microwave.

  • A multimeter can be used to measure the resistance of the diode. The multimeter must be on the resistance setting or the diode check setting. If the diode reads zero in both directions, then it is broken.

Ajouter un commentaire

Sparking inside of the microwave may also be the result of a broken or misaligned magnetron. If this is the case, it is recommended to take the microwave to a qualified professional or completely discarding the unit and purchasing a new one.
  • Sparking inside of the microwave may also be the result of a broken or misaligned magnetron. If this is the case, it is recommended to take the microwave to a qualified professional or completely discarding the unit and purchasing a new one.

  • Fixing the magnetron without the aid of a qualified professional is NOT recommended. The magnetron is an emitter of microwave radiation and tampering with it may lead to serious injury or death.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

5 autre(s) ont terminé cette réparation.

Michael

Membre depuis le 26/09/2012

183 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 2-12, Propen Fall 2012 Membre de l'équipe Cal Poly, Team 2-12, Propen Fall 2012

CPSU-PROPEN-F12S2G12

3 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 5

30 derniers jours : 26

Total : 2,820