Introduction

This process involves removing the back cover and the front cover of the camera.

Pièces

Aucune pièce nécessaire.

Unscrew a total of seven screws from the left, right, bottom, and back sides of the camera. Unscrew a total of seven screws from the left, right, bottom, and back sides of the camera.
  • Unscrew a total of seven screws from the left, right, bottom, and back sides of the camera.

Ajouter un commentaire

To remove back cover, begin by loosening the back cover from both the left and the right sides of the camera. Remove back cover. After the back cover is removed, the lid of the battery compartment may fall off because it is not securely attached to anything. Remove back cover. After the back cover is removed, the lid of the battery compartment may fall off because it is not securely attached to anything.
  • To remove back cover, begin by loosening the back cover from both the left and the right sides of the camera.

  • Remove back cover. After the back cover is removed, the lid of the battery compartment may fall off because it is not securely attached to anything.

Ajouter un commentaire

In order to remove the front cover, the film compartment must be opened. To open the film compartment, place your finger on top of the grey latch on the left side of the camera. Push down on the grey latch. The film compartment door should pop open.
  • In order to remove the front cover, the film compartment must be opened.

  • To open the film compartment, place your finger on top of the grey latch on the left side of the camera.

  • Push down on the grey latch. The film compartment door should pop open.

Ajouter un commentaire

The following step to remove the film compartment door is optional. However, it may aid in the maneuvering of the camera in future steps. To remove the film compartment door, take a thin object such as a toothpick or a small screwdriver and push down on the metal pin holding the film compartment door in place. After pushing the metal pin down, use your fingers to completely remove the metal pin.
  • The following step to remove the film compartment door is optional. However, it may aid in the maneuvering of the camera in future steps.

  • To remove the film compartment door, take a thin object such as a toothpick or a small screwdriver and push down on the metal pin holding the film compartment door in place.

  • After pushing the metal pin down, use your fingers to completely remove the metal pin.

  • After the metal pin has been removed, the film compartment door can be removed.

Ajouter un commentaire

Unscrew two screws from within the film compartment. These screws are located at the bottom left and the middle right and require a thin shaft screwdriver. Unscrew two screws from within the film compartment. These screws are located at the bottom left and the middle right and require a thin shaft screwdriver.
  • Unscrew two screws from within the film compartment. These screws are located at the bottom left and the middle right and require a thin shaft screwdriver.

Ajouter un commentaire

To remove the front cover, begin by loosening the front cover from the left and the right sides of the camera. Remove the front cover. Remove the front cover.
  • To remove the front cover, begin by loosening the front cover from the left and the right sides of the camera.

  • Remove the front cover.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Eric Dazet

Membre depuis le 10/04/2012

352 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 6-21, Amido Spring 2012 Membre de l'équipe Cal Poly, Team 6-21, Amido Spring 2012

CPSU-AMIDO-S12S6G21

4 membres

14 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 5

Total : 221