Pièces

Aucune pièce nécessaire.

Make sure the toaster is unplugged before starting. Burnt hair smells even worse than burnt toast! Turn the toaster upside down and remove the rubber stopper "feet" with your fingers.
  • Make sure the toaster is unplugged before starting. Burnt hair smells even worse than burnt toast!

  • Turn the toaster upside down and remove the rubber stopper "feet" with your fingers.

Ajouter un commentaire

Using a #2 phillips head screwdriver, remove the four 12mm screws that attach the shell to the rest of the toaster. Using a #2 phillips head screwdriver, remove the four 12mm screws that attach the shell to the rest of the toaster.
  • Using a #2 phillips head screwdriver, remove the four 12mm screws that attach the shell to the rest of the toaster.

Ajouter un commentaire

With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster. When reassembling the toaster, make sure that the back of the dial lines up with the slot both in position and orientation (the dial and slot are not perfect  circles - they have a notch). The only object holding the shell onto the  toaster now is the grey part of the lever.
  • With the dial facing you, push the toaster base up and away until the base is just over the lip of the shell. This will disconnect the browning dial from the rest of the toaster.

  • When reassembling the toaster, make sure that the back of the dial lines up with the slot both in position and orientation (the dial and slot are not perfect circles - they have a notch).

  • The only object holding the shell onto the toaster now is the grey part of the lever.

Ajouter un commentaire

Reach under the shell and grab the back, white part of the lever.
  • Reach under the shell and grab the back, white part of the lever.

  • Grab the grey lever between your index finger and your middle finger and pull.

  • Pulling too hard will break the mechanism that holds the grey handle onto the white lever.

  • Remove the shell.

Ajouter un commentaire

Locate the black, diamond shaped spring behind the white lever bracket.
  • Locate the black, diamond shaped spring behind the white lever bracket.

Ajouter un commentaire

To remove the spring, use the tweezers to push the bottom edge of the spring out and around the metal bracket that keeps the springs in place.
  • To remove the spring, use the tweezers to push the bottom edge of the spring out and around the metal bracket that keeps the springs in place.

  • Repeat this for the other side.

Ajouter un commentaire

Pulling the bottom of the spring out, lift the left circle up over the metal bracket that extends out from the bread grabbers.
  • Pulling the bottom of the spring out, lift the left circle up over the metal bracket that extends out from the bread grabbers.

  • Bring the right circle out, down, and around the bracket the extends out from the shelf that the toast would sits on.

  • Remove the right circle.

Ajouter un commentaire

Make sure that all the angles are similar to the other metal spring.
  • Make sure that all the angles are similar to the other metal spring.

  • If not, then bend the broken spring to the angles of the correct spring.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Grant Haug

Membre depuis le 26/09/2012

115 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 2-8, Propen Fall 2012 Membre de l'équipe Cal Poly, Team 2-8, Propen Fall 2012

CPSU-PROPEN-F12S2G8

5 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 3

30 derniers jours : 13

Total : 2,130