Introduction

How to replace the screen on a Samsung Captivate Glide.

Remove back cover using fingernail or plastic opening tool. The cover pulls up and off. Remove back cover using fingernail or plastic opening tool. The cover pulls up and off. Remove back cover using fingernail or plastic opening tool. The cover pulls up and off.
  • Remove back cover using fingernail or plastic opening tool. The cover pulls up and off.

Ajouter un commentaire

Remove battery with plastic opening tool or finger. Remove battery with plastic opening tool or finger.
  • Remove battery with plastic opening tool or finger.

Ajouter un commentaire

Remove the seven screws from backplate using the #00 screwdriver. Remove the seven screws from backplate using the #00 screwdriver.
  • Remove the seven screws from backplate using the #00 screwdriver.

Ajouter un commentaire

Remove the back plate using the plastic opening tool. There is a lip on each side, and both must be pried up. You can work your way around the edges after prying the two sides.
  • Remove the back plate using the plastic opening tool.

  • There is a lip on each side, and both must be pried up.

  • You can work your way around the edges after prying the two sides.

Ajouter un commentaire

Use the plastic opening tool to detach the two tabs connecting the motherboard to the base of the phone. Use the plastic opening tool to detach the two tabs connecting the motherboard to the base of the phone.
  • Use the plastic opening tool to detach the two tabs connecting the motherboard to the base of the phone.

Ajouter un commentaire

Disconnect the antenna cable from the motherboard using tweezers.
  • Disconnect the antenna cable from the motherboard using tweezers.

Ajouter un commentaire

Remove the single screw connecting the motherboard to the base of the phone by using the #00 Phillips screwdriver.
  • Remove the single screw connecting the motherboard to the base of the phone by using the #00 Phillips screwdriver.

Ajouter un commentaire

Lift the motherboard out of the base of the phone. Lift the motherboard out of the base of the phone.
  • Lift the motherboard out of the base of the phone.

Ajouter un commentaire

Remove the eight screws with the #00 screwdriver. Remove the eight screws with the #00 screwdriver.
  • Remove the eight screws with the #00 screwdriver.

Ajouter un commentaire

Remove blue tape using the tweezers. Remove blue tape using the tweezers.
  • Remove blue tape using the tweezers.

Ajouter un commentaire

Remove screws with the #00 screwdriver.
  • Remove screws with the #00 screwdriver.

Ajouter un commentaire

Using the plastic opening tool, remove the back plate by prying on the four main points.
  • Using the plastic opening tool, remove the back plate by prying on the four main points.

    • You may encounter difficultly at certain points. Work the plastic opening tool along the edge to keep back plate from closing again.

Ajouter un commentaire

Lift the back plate.
  • Lift the back plate.

  • To remove to slide flex cable, gently peel back from the back plate and remove back plate.

Ajouter un commentaire

Slide the flex cable through the slot. Be careful to not tear the cable. Set the front plate down. Set the front plate down.
  • Slide the flex cable through the slot. Be careful to not tear the cable.

  • Set the front plate down.

Ajouter un commentaire

Remove the four corner screws using the #00 screwdriver. Remove the four corner screws using the #00 screwdriver.
  • Remove the four corner screws using the #00 screwdriver.

Ajouter un commentaire

Using the plastic opening tool, release all the clips on all four sides holding the screen assembly. You can now remove the back plate by sliding the flex cable through the slot. You can now remove the back plate by sliding the flex cable through the slot.
  • Using the plastic opening tool, release all the clips on all four sides holding the screen assembly.

  • You can now remove the back plate by sliding the flex cable through the slot.

Ajouter un commentaire

Use the plastic opening tool to release the main jaw connector, front speaker and camera. Use the plastic opening tool to release the main jaw connector, front speaker and camera. Use the plastic opening tool to release the main jaw connector, front speaker and camera.
  • Use the plastic opening tool to release the main jaw connector, front speaker and camera.

Ajouter un commentaire

By using the plastic opening tool you can release the keypad flex cable from the jaw connecter clamp. By using the plastic opening tool you can release the keypad flex cable from the jaw connecter clamp.
  • By using the plastic opening tool you can release the keypad flex cable from the jaw connecter clamp.

Ajouter un commentaire

Use a heat gun or blow dryer. Heat the outside edges using quick movements for about 45 seconds.
  • Use a heat gun or blow dryer.

  • Heat the outside edges using quick movements for about 45 seconds.

Ajouter un commentaire

Using the plastic opening tool to pry around the edges, release the touch screen from the screen frame. Using the plastic opening tool to pry around the edges, release the touch screen from the screen frame. Using the plastic opening tool to pry around the edges, release the touch screen from the screen frame.
  • Using the plastic opening tool to pry around the edges, release the touch screen from the screen frame.

Ajouter un commentaire

While adhesive is still warm, use the plastic opening tool to gently remove the keyboard flex cable from the screen. You can now replace the screen assembly. You can now replace the screen assembly.
  • While adhesive is still warm, use the plastic opening tool to gently remove the keyboard flex cable from the screen.

  • You can now replace the screen assembly.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Tyler Moore

Membre depuis le 23/09/2014

136 Réputation

1 tutoriel rédigé

Équipe

USF Tampa, Team 5-3, Mcgee Fall 2014 Membre de l'équipe USF Tampa, Team 5-3, Mcgee Fall 2014

USFT-MCGEE-F14S5G3

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 5

Total : 680