Introduction

If the lens of the video camera cracks or becomes cloudy, replacing it can be costly and confusing. This guide shows how you can access the lens assembly on your own to make a quick replacement. To get to the lens assembly, you will need to have already removed the battery and the outer casing.

Lift viewfinder to access battery pack.
  • Lift viewfinder to access battery pack.

Ajouter un commentaire

Press the battery release button. While pushing the battery button, slide the battery to the left.
  • Press the battery release button.

  • While pushing the battery button, slide the battery to the left.

Ajouter un commentaire

Pull the battery pack out of the video camera.
  • Pull the battery pack out of the video camera.

Ajouter un commentaire

Open the cassette cover. Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm. Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm.
  • Open the cassette cover.

  • Unscrew 14 screws located on the outer casing. Three are located on the top face 2x6.8mm and 1X4.54mm, three on the left face 1x4.54mm,1x5.3mm and seven on the bottom face 5x4.54mm and 2x6.77mm.

Ajouter un commentaire

Continue removing screws. Five on the right side, from bottom to top, 3x4.54mm 2x5.70mm. One on the backside 1x4.54mm. Continue removing screws. Five on the right side, from bottom to top, 3x4.54mm 2x5.70mm. One on the backside 1x4.54mm.
  • Continue removing screws. Five on the right side, from bottom to top, 3x4.54mm 2x5.70mm. One on the backside 1x4.54mm.

Ajouter un commentaire

Pull off the plastic tape cover by lifting it up and out of the camera base.
  • Pull off the plastic tape cover by lifting it up and out of the camera base.

Ajouter un commentaire

Disconnect the mic assembly by pulling it away from the camera base.
  • Disconnect the mic assembly by pulling it away from the camera base.

  • Do not pull too hard as the wires are still connected.

Ajouter un commentaire

Pull the bottom part of the case away from the camera.
  • Pull the bottom part of the case away from the camera.

Ajouter un commentaire

Remove the three marked screws located on the right face of the video camera 3x4.54mm.
  • Remove the three marked screws located on the right face of the video camera 3x4.54mm.

Ajouter un commentaire

Remove the one circuit board screw at the front of the video camera 1x3.6mm.
  • Remove the one circuit board screw at the front of the video camera 1x3.6mm.

Ajouter un commentaire

Pull the audio/video inputs underneath the microphone assembly. The inputs should still be connected to the circuit board.
  • Pull the audio/video inputs underneath the microphone assembly. The inputs should still be connected to the circuit board.

Ajouter un commentaire

Remove two remaining case screws on the front of the camera 2x3.63mm.
  • Remove two remaining case screws on the front of the camera 2x3.63mm.

Ajouter un commentaire

Using metal tweezers, pull out the plastic connector box on the front side. Again use metal tweezers to pull out the connection box on the bottom of the camera. The right side of the case can now be removed by pulling it to the right.
  • Using metal tweezers, pull out the plastic connector box on the front side.

  • Again use metal tweezers to pull out the connection box on the bottom of the camera. The right side of the case can now be removed by pulling it to the right.

Ajouter un commentaire

Remove three screws from the circuit board on the left side of the video camera 3x3.6mm.
  • Remove three screws from the circuit board on the left side of the video camera 3x3.6mm.

Ajouter un commentaire

Using metal tweezers, pull out the plastic connector box. Pull up the circuit board. Be careful, it should still be connected to a band wire.
  • Using metal tweezers, pull out the plastic connector box.

  • Pull up the circuit board. Be careful, it should still be connected to a band wire.

Ajouter un commentaire

Remove three 2x4.45mm 1x5.36mm screws around lens assembly. Remove three 2x4.45mm 1x5.36mm screws around lens assembly. Remove three 2x4.45mm 1x5.36mm screws around lens assembly.
  • Remove three 2x4.45mm 1x5.36mm screws around lens assembly.

Ajouter un commentaire

Remove three screws from the bottom part of the lens assembly 2x6.00mm and 1x5.46mm. Be careful not to break band wires. The bottom two are gold screws.
  • Remove three screws from the bottom part of the lens assembly 2x6.00mm and 1x5.46mm. Be careful not to break band wires. The bottom two are gold screws.

Ajouter un commentaire

Lift lens assembly off large circuit board. Unscrew three top screws 2x5.31mm and 1x6.07mm.
  • Lift lens assembly off large circuit board.

  • Unscrew three top screws 2x5.31mm and 1x6.07mm.

  • Unscrew last remaining screw with Phillips #000 screwdriver 1x6.06mm. Lens should detach from lens assembly.

Ajouter un commentaire

Once lens has been removed from lens assembly, replacement or repair is possible.
  • Once lens has been removed from lens assembly, replacement or repair is possible.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Andrew

Membre depuis le 23/01/2011

58 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 11-25, Maness Winter 2011 Membre de l'équipe Cal Poly, Team 11-25, Maness Winter 2011

CPSU-MANESS-W11S11G25

4 membres

4 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 4

Total : 2,167