Introduction

Replacing a defective LCD screen.

The screws from the camera are extremely small so it is a good idea to have a small container to hold all the screws as you remove them.
  • The screws from the camera are extremely small so it is a good idea to have a small container to hold all the screws as you remove them.

Ajouter un commentaire

Take your screwdriver and remove the bottom screws of the camera. (The picture shows the lens facing away from you and the LCD facing you.) There should be four silver screws.
  • Take your screwdriver and remove the bottom screws of the camera. (The picture shows the lens facing away from you and the LCD facing you.) There should be four silver screws.

Ajouter un commentaire

On the right side of the camera, remove the two screws using the screwdriver. There will be two silver screws. (The picture shows the lens facing away from you and LCD screen facing you.)
  • On the right side of the camera, remove the two screws using the screwdriver. There will be two silver screws. (The picture shows the lens facing away from you and LCD screen facing you.)

Ajouter un commentaire

On the left side of the camera, remove the two screws using the screwdriver. There will be two silver screws. (The picture shows the lens facing away from you and the LCD screen facing you.)
  • On the left side of the camera, remove the two screws using the screwdriver. There will be two silver screws. (The picture shows the lens facing away from you and the LCD screen facing you.)

Ajouter un commentaire

Gently remove the back casing by holding onto both sides of the camera and pulling them apart.
  • Gently remove the back casing by holding onto both sides of the camera and pulling them apart.

Ajouter un commentaire

Now, carefully pull off the back cover.
  • Now, carefully pull off the back cover.

Ajouter un commentaire

The two halves of the camera casing should now be separate.
  • The two halves of the camera casing should now be separate.

Ajouter un commentaire

Keep track of the small screws that you remove.
  • Keep track of the small screws that you remove.

  • Opening, removing and/or replacing the front casing may void your manufacturers warranty

Ajouter un commentaire

Remove the two screws at the top of the camera casing.
  • Remove the two screws at the top of the camera casing.

There was no screw in the left hand location shown, when disassembling my camera for the first time.

Chas - Réponse

Gently pop open the plastic piece as shown.
  • Gently pop open the plastic piece as shown.

Ajouter un commentaire

Remove the screw connecting the front casing to the electrical components as shown.
  • Remove the screw connecting the front casing to the electrical components as shown.

Ajouter un commentaire

Gently loosen and remove the side casing by firmly pulling with your fingers.
  • Gently loosen and remove the side casing by firmly pulling with your fingers.

  • Take care not to break the fragile part or to scratch the LCD screen.

Ajouter un commentaire

Remove the two screws connecting the front casing to the electrical components.
  • Remove the two screws connecting the front casing to the electrical components.

Ajouter un commentaire

Gently loosen the front casing.
  • Gently loosen the front casing.

  • Be careful not to scratch any of the exposed electrical components.

Ajouter un commentaire

Fully remove the front casing from the camera.
  • Fully remove the front casing from the camera.

Ajouter un commentaire

Remove the last screw holding the LCD/control panel to the rest of the camera on the right hand side. Looking at the right side of the camera, this last screw is in the bottom left corner. (There were two other screws that were removed when taking the back cover off, thus it is important to pay attention to which hole this screw comes out of for reassembly.)
  • Remove the last screw holding the LCD/control panel to the rest of the camera on the right hand side. Looking at the right side of the camera, this last screw is in the bottom left corner. (There were two other screws that were removed when taking the back cover off, thus it is important to pay attention to which hole this screw comes out of for reassembly.)

Ajouter un commentaire

At this point, all screws on the left and right sides of the camera should be removed. Paying careful attention to the right side's electrical wiring, gently pull the left side of the LCD plate away from the rest of the camera.
  • At this point, all screws on the left and right sides of the camera should be removed.

  • Paying careful attention to the right side's electrical wiring, gently pull the left side of the LCD plate away from the rest of the camera.

  • DO NOT detach the electrical wiring connecting the right side of the LCD and the camera.

Ajouter un commentaire

NOTE: This picture is simply used to identify the action required to release the electrical ribbons, but not the proper location for this step.
  • NOTE: This picture is simply used to identify the action required to release the electrical ribbons, but not the proper location for this step.

  • This step applies to the larger electrical ribbon connecting the LCD screen and circuit board.

  • Using a spudger, wedge the flat tipped end between the black bar and the circuit board.

  • Carefully lift the black bar into the vertical position.

Ajouter un commentaire

After raising the black bar, the electrical ribbon is free from its port.
  • After raising the black bar, the electrical ribbon is free from its port.

  • Use tweezers to carefully pull larger electrical ribbon from its circuit board port.

Ajouter un commentaire

The smaller electrical ribbon, to the left of the larger ribbon, does not have a black bar securing it in place.
  • The smaller electrical ribbon, to the left of the larger ribbon, does not have a black bar securing it in place.

  • Use tweezers to carefully pull smaller electrical ribbon from its circuit board port.

Ajouter un commentaire

Desolder the small electrical ribbon that connects the control panel to the LCD screen.
  • Desolder the small electrical ribbon that connects the control panel to the LCD screen.

  • Now the LCD/control panel is completely removed from the part and ready to be replaced.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Brent Clavin

Membre depuis le 15/04/2010

54 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 33-73, Johann Spring 2010 Membre de l'équipe Cal Poly, Team 33-73, Johann Spring 2010

CPSU-JOHANN-S10S33G73

3 membres

2 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 5

30 derniers jours : 7

Total : 9,210