Introduction

Replace lens.

Remove Memory Stick Pro from the card reader slot on the bottom of the camera.
  • Remove Memory Stick Pro from the card reader slot on the bottom of the camera.

  • Remove both batteries.

Ajouter un commentaire

Remove the single visible screw from both sides of the camera. Remove the two screws that are adjacent to the warning label, which is on the underside of the camera.
  • Remove the single visible screw from both sides of the camera.

  • Remove the two screws that are adjacent to the warning label, which is on the underside of the camera.

  • Do NOT remove all four screws from the bottom.

Ajouter un commentaire

Gently remove the back cover from the camera. The first time the case is removed, it will be stiff. Be patient and gently rock the cover back and forth until it slides free.
  • Gently remove the back cover from the camera.

  • The first time the case is removed, it will be stiff. Be patient and gently rock the cover back and forth until it slides free.

Ajouter un commentaire

Remove the two screws holding the circuit board down. Remove the two screws holding the circuit board down.
  • Remove the two screws holding the circuit board down.

Ajouter un commentaire

Detach the orange cable from the board.
  • Detach the orange cable from the board.

  • Use a thin object, like a paperclip, to gently pry the cable off the connector.

Ajouter un commentaire

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
The LCD screen sits in two slots; one on the bottom, and one on the left edge. Slide LCD screen from the two slots.
  • The LCD screen sits in two slots; one on the bottom, and one on the left edge.

  • Slide LCD screen from the two slots.

  • Do not attempt to completely remove the screen, as it is still attached to the camera.

Ajouter un commentaire

To remove the LCD screen, detach the orange cable from the board. If needed, replace the LCD screen. If needed, replace the LCD screen.
  • To remove the LCD screen, detach the orange cable from the board.

  • If needed, replace the LCD screen.

Ajouter un commentaire

Remove the two screws holding down the steel back plate. Remove steel back plate.
  • Remove the two screws holding down the steel back plate.

  • Remove steel back plate.

Ajouter un commentaire

Now remove the plastic plate that covers the motherboard. Now remove the plastic plate that covers the motherboard.
  • Now remove the plastic plate that covers the motherboard.

Below and to the left of the viewfinder there is a vertical slot in the motherboard with a soldered connection to the flash capacitor on each side. Using a small screwdriver with an INSULATED handle, short these together for several seconds to discharge the potentially dangerous charge.

Philip Le Riche - Réponse

Warning: Electric Shock From this point on, hold the camera by the chrome edges ONLY.  Capacitors store electric charge even if the batteries are removed. Remove the blue cable.
  • Warning: Electric Shock From this point on, hold the camera by the chrome edges ONLY. Capacitors store electric charge even if the batteries are removed.

  • Remove the blue cable.

Ajouter un commentaire

Disconnect the flash cable (black and white wires) before completely removing the front case. Gently start to remove the case.
  • Disconnect the flash cable (black and white wires) before completely removing the front case.

  • Gently start to remove the case.

  • Once the cable is free, set aside the front case.

If the front doesn't seem to want to come away, maybe the flash cable is caught around its socket.

Philip Le Riche - Réponse

The speaker should now be clearly seen on the underside of the camera. Gently unplug the speaker from the motherboard.
  • The speaker should now be clearly seen on the underside of the camera.

  • Gently unplug the speaker from the motherboard.

  • Replace the speaker.

Ajouter un commentaire

Remove the orange cable connecting the battery terminal to the motherboard. Remove the orange cable connecting the battery terminal to the motherboard.
  • Remove the orange cable connecting the battery terminal to the motherboard.

Ajouter un commentaire

The battery terminal is now free from the board and can be slid out.
  • The battery terminal is now free from the board and can be slid out.

Ajouter un commentaire

Detach two cables that go from the motherboard to the lens. Remove lens. Remove lens.
  • Detach two cables that go from the motherboard to the lens.

  • Remove lens.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

6 autre(s) ont terminé cette réparation.

Thomas

Membre depuis le 14/04/2010

109 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 15-50, Garner Spring 2010 Membre de l'équipe Cal Poly, Team 15-50, Garner Spring 2010

CPSU-GARNER-S10S15G50

5 membres

6 tutoriels rédigés

Ifixit it's so awesome... For a guy who loves to bring things apart but is scared of how to do it ifixit is wonderful

ogunkayodesamuel - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 16

30 derniers jours : 132

Total : 17,946