To remove the speaker grill, insert the big spudger underneath it in each corner.
  • To remove the speaker grill, insert the big spudger underneath it in each corner.

  • Work around the edges to pry the grill up and off.

Ajouter un commentaire

With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame. This will need to be done on all four sides of the speaker to remove all four panels
  • With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame.

  • This will need to be done on all four sides of the speaker to remove all four panels

  • This requires some effort because the adhesive is sticky.

Ajouter un commentaire

Locate the four screws on the now exposed front panel. Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).
  • Locate the four screws on the now exposed front panel.

  • Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).

Ajouter un commentaire

Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.
  • Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.

  • Use the same T7 screwdriver head here.

  • Remove each of the four corner screws (15.0 mm long).

Ajouter un commentaire

With a little force, carefully lift the lid of the speaker.
  • With a little force, carefully lift the lid of the speaker.

  • Make sure that you do not pull on the wires.

Ajouter un commentaire

Unclip the four wire connectors (that are attached to the speaker lid). Unclip the four wire connectors (that are attached to the speaker lid). Unclip the four wire connectors (that are attached to the speaker lid).
  • Unclip the four wire connectors (that are attached to the speaker lid).

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Separate the speaker lid from the bottom frame.
  • Separate the speaker lid from the bottom frame.

  • To prepare the speaker for the next step place the lid parallel to the frame.

Ajouter un commentaire

Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.
  • Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.

  • Using the screwdriver with bit PH1, unscrew each screw.

Ajouter un commentaire

Separate the speaker lid entirely from the bottom frame.
  • Separate the speaker lid entirely from the bottom frame.

Ajouter un commentaire

Remove the top screw (10 mm).
  • Remove the top screw (10 mm).

  • Use the screwdriver with bit T7.

Ajouter un commentaire

Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7. There are two screws on the left side of the white box and one to its right.
  • Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7.

  • There are two screws on the left side of the white box and one to its right.

Ajouter un commentaire

Slightly lift the white box with all the wires still attached.
  • Slightly lift the white box with all the wires still attached.

Ajouter un commentaire

Take the big spudger and pry the black casing up from the circuit box. Take the big spudger and pry the black casing up from the circuit box.
  • Take the big spudger and pry the black casing up from the circuit box.

Ajouter un commentaire

Locate the blue film attached to the circuit box containing the charging port.
  • Locate the blue film attached to the circuit box containing the charging port.

  • Detach the blue film from the box.

Ajouter un commentaire

Detach the yellow, black and red wires by pulling them directly up.
  • Detach the yellow, black and red wires by pulling them directly up.

Ajouter un commentaire

Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement. Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.
  • Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.

Ajouter un commentaire

Locate the black, yellow, and red wires and steadily pull them smooth if they are tangled.
  • Locate the black, yellow, and red wires and steadily pull them smooth if they are tangled.

Ajouter un commentaire

Unravel any tangled wires or replace any damaged wires.
  • Unravel any tangled wires or replace any damaged wires.

  • The wires should all run parallel to one another.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Isabella Durazo

Membre depuis le 09/04/2018

126 Réputation

1 tutoriel rédigé

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 5

30 derniers jours : 18

Total : 18