Introduction

You will need to use a source of heat. You may need to buy adhesive for the reassembly. Make sure the phone is completely powered off before opening the device.

Apply heat  on the back surface of the phone.
  • Apply heat on the back surface of the phone.

  • Continue to heat the device as needed throughout the replacement process.

  • The device can get very hot, so be careful when handling it.

Ajouter un commentaire

Stick the small suction cup on the bottom half of the back surface of the phone.
  • Stick the small suction cup on the bottom half of the back surface of the phone.

Ajouter un commentaire

With the bottom of the device facing you, lift up on the suction cup handle. Use the plastic opening tool around all sides to pry off the back cover. Use the plastic opening tool around all sides to pry off the back cover.
  • With the bottom of the device facing you, lift up on the suction cup handle.

  • Use the plastic opening tool around all sides to pry off the back cover.

Ajouter un commentaire

Pull the back of the phone case away from the device. You will hear popping sounds of glue being ripped from the phone. You will hear the sound of the back unlatching from the device.
  • Pull the back of the phone case away from the device.

  • You will hear popping sounds of glue being ripped from the phone.

  • You will hear the sound of the back unlatching from the device.

  • You will need to apply adhesive or glue along the device to have maximum seal in reassembly.

  • RAF antenna may be attached to the back cover upon removal.

Ajouter un commentaire

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Apply heat to the copper RAF antenna.
  • Apply heat to the copper RAF antenna.

  • This step and the following step only apply if the RAF antenna does not come off when taking the back cover off.

Ajouter un commentaire

Peel back the RAF antenna.
  • Peel back the RAF antenna.

Ajouter un commentaire

Remove the five black 4mm screws with a Phillips #00 screwdriver. Remove the five black 4mm screws with a Phillips #00 screwdriver.
  • Remove the five black 4mm screws with a Phillips #00 screwdriver.

Ajouter un commentaire

Pry up the black camera case with the plastic opening tool and then remove the case. Pry up the black camera case with the plastic opening tool and then remove the case. Pry up the black camera case with the plastic opening tool and then remove the case.
  • Pry up the black camera case with the plastic opening tool and then remove the case.

Ajouter un commentaire

Use the flat end of the spudger to peel up the copper tab to the right of the back camera. Peel back the tab past the connector.
  • Use the flat end of the spudger to peel up the copper tab to the right of the back camera.

  • Peel back the tab past the connector.

  • Tab is stuck with adhesive.

Ajouter un commentaire

Pry up the camera's connector to the motherboard with the nylon spudger.
  • Pry up the camera's connector to the motherboard with the nylon spudger.

Ajouter un commentaire

Use the flat end of the nylon spudger to lift the camera out of the phone.
  • Use the flat end of the nylon spudger to lift the camera out of the phone.

Ajouter un commentaire

Finish removing the front camera by lifting it gently with your fingers.
  • Finish removing the front camera by lifting it gently with your fingers.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Theresa Wilcoski

Membre depuis le 18/04/2018

267 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team S17-G2, Livingston Spring 2018 Membre de l'équipe Cal Poly, Team S17-G2, Livingston Spring 2018

CPSU-LIVINGSTON-S18S17G2

4 membres

8 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 14

Total : 31