Introduction

In the rare case of a power surge, if the device is not plugged into a surge protecting outlet, the fuse will blow out and need to be replaced. This guide will show how to tear the whole projector down to get the fuse and replace it.

Start by removing the two screws on the bottom of the device as shown. Start by removing the two screws on the bottom of the device as shown. Start by removing the two screws on the bottom of the device as shown.
  • Start by removing the two screws on the bottom of the device as shown.

Ajouter un commentaire

Remove the top plastic cover from the device. The back is snapped on so it would help to have leverage from a prying tool. Remove the ribbon cable attached to the plastic piece just removed. Remember its orientation for re-assembling later.
  • Remove the top plastic cover from the device. The back is snapped on so it would help to have leverage from a prying tool.

  • Remove the ribbon cable attached to the plastic piece just removed. Remember its orientation for re-assembling later.

Ajouter un commentaire

Remove the screws from the case located around the device. Remove the screws from the case located around the device. Remove the screws from the case located around the device.
  • Remove the screws from the case located around the device.

Ajouter un commentaire

Remove the plastic panels from the body.
  • Remove the plastic panels from the body.

Ajouter un commentaire

Kits RAM pour Mac
Accélérez votre Mac. Maximisez sa mémoire.
Kits RAM pour Mac
Augmentez la mémoire de votre Mac.
Remove the screws from the IO panel. Pull up on the panel and remove it. Pull up on the panel and remove it.
  • Remove the screws from the IO panel.

  • Pull up on the panel and remove it.

Ajouter un commentaire

Unscrew the screws from the metal shielding to remove it. Unscrew the screws from the metal shielding to remove it.
  • Unscrew the screws from the metal shielding to remove it.

Ajouter un commentaire

Remove cables from motherboard. Unscrew motherboard and remove from device. Unscrew motherboard and remove from device.
  • Remove cables from motherboard.

  • Unscrew motherboard and remove from device.

How many cables? Can you mark them?

lkmemphis - Réponse

Remove the cable from the bottom of the motherboard to fully remove it.
  • Remove the cable from the bottom of the motherboard to fully remove it.

Does this show the cable removed or not removed? Is it the set of wires encased in blue? Or is it the larger white thingie o the right of the elevated motherboard?

lkmemphis - Réponse

Unscrew the power adapter on the back.
  • Unscrew the power adapter on the back.

Ajouter un commentaire

Remove cables from the power supply board. Remove the screws located around the board to un-mount it.
  • Remove cables from the power supply board.

  • Remove the screws located around the board to un-mount it.

Ajouter un commentaire

Locate the fuse near where the power adapter was. De-solder the fuse and replace with an equivalent fuse (Fuse leads to de-solder are marked in red).
  • Locate the fuse near where the power adapter was.

  • De-solder the fuse and replace with an equivalent fuse (Fuse leads to de-solder are marked in red).

Will this reference to where the power adapter was be meaningful? Forgive me, but this is like directions that say “turn left at where the A&W used to be”

Is that green panel turned upside down in the second image?

Is that brownish thing the fuse?

lkmemphis - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

Bryan Underwood

Membre depuis le 02/04/2018

697 Réputation

5 tutoriels rédigés

Équipe

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 6

Total : 25