Introduction

This guide will show you how to replace the speakers in your Toshiba Thrive.

Make sure the lock switch for the back cover is unlocked.
  • Make sure the lock switch for the back cover is unlocked.

    • The cover is unlocked when the switch is slid in the direction of the 'unlock' icon.

Ajouter un commentaire

Remove back cover by prying away from the Thrive. The easiest place to pry from is one of the two speakers.
  • Remove back cover by prying away from the Thrive.

    • The easiest place to pry from is one of the two speakers.

Ajouter un commentaire

To remove the battery, make sure the lock switch is in the unlocked position.
  • To remove the battery, make sure the lock switch is in the unlocked position.

    • The battery is unlocked when the switch is slid to the unlocked position.

Ajouter un commentaire

Slide the battery switch release to the right. While holding the switch in place, lift up the battery. While holding the switch in place, lift up the battery.
  • Slide the battery switch release to the right.

    • While holding the switch in place, lift up the battery.

Ajouter un commentaire

Start by using a PH0 phillips head screwdriver to remove the 12 screws holding on the back cover All of these screws are identical so don't worry about getting them mixed up.
  • Start by using a PH0 phillips head screwdriver to remove the 12 screws holding on the back cover

    • All of these screws are identical so don't worry about getting them mixed up.

Ajouter un commentaire

Start to gently pry the back of the device off, while leaving it loosely in place. Be careful not to tear or damage the cables when removing the back. Be careful not to tear or damage the cables when removing the back.
  • Start to gently pry the back of the device off, while leaving it loosely in place.

    • Be careful not to tear or damage the cables when removing the back.

Ajouter un commentaire

Once the back of the case is off, disconnect the wires by gently pulling on the plastic tabs as shown. Once the back of the case is off, disconnect the wires by gently pulling on the plastic tabs as shown. Once the back of the case is off, disconnect the wires by gently pulling on the plastic tabs as shown.
  • Once the back of the case is off, disconnect the wires by gently pulling on the plastic tabs as shown.

Ajouter un commentaire

carefully open the device like a book and lay the two halves beside each other. put the screen assembly in a safe place as you complete the rest of the guide.
  • carefully open the device like a book and lay the two halves beside each other.

  • put the screen assembly in a safe place as you complete the rest of the guide.

Ajouter un commentaire

Use the plastic opening tool to open the latch holding the last wire to the back of the device. Use the plastic opening tool to open the latch holding the last wire to the back of the device.
  • Use the plastic opening tool to open the latch holding the last wire to the back of the device.

this is the step you need on the other step i commented on

Sun Fai Lau - Réponse

Remove the two screws holding the speakers in place.  The screws are 3mm in length and require a PH0 screwdriver. Using a pair of tweezers, remove the speaker. Using a pair of tweezers, remove the speaker.
  • Remove the two screws holding the speakers in place. The screws are 3mm in length and require a PH0 screwdriver.

  • Using a pair of tweezers, remove the speaker.

Ajouter un commentaire

Use the tweezers to help you remove the speaker wire from the clips holding them in place. After removal place the left speaker on the side. After removal place the left speaker on the side.
  • Use the tweezers to help you remove the speaker wire from the clips holding them in place.

  • After removal place the left speaker on the side.

Ajouter un commentaire

Use the tweezers again to help you remove the right speaker from its position. Use a plastic opening tool to pull the connector connecting the speaker to the motherboard out of its port. Use a plastic opening tool to pull the connector connecting the speaker to the motherboard out of its port.
  • Use the tweezers again to help you remove the right speaker from its position.

  • Use a plastic opening tool to pull the connector connecting the speaker to the motherboard out of its port.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Ivan Williams

Membre depuis le 22/09/2014

127 Réputation

1 tutoriel rédigé

Équipe

USF Tampa, Team 10-1, Brown Fall 2014 Membre de l'équipe USF Tampa, Team 10-1, Brown Fall 2014

USFT-BROWN-F14S10G1

3 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 227